UNLIMITED FREE
ACCESS TO THE WORLD'S BEST IDEAS

SUBMIT
Already a GlobalSpec user? Log in.

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

Customize Your GlobalSpec Experience

Select Your Free Newsletters

Industry Newsletters

Select Your Free Product Alerts

Finish!
Privacy Policy

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

BSI - BS EN 60794-5

Optical fibre cables Part 5: Sectional specification — Microduct cabling for installation by blowing

active, Most Current
Buy Now
Organization: BSI
Publication Date: 31 December 2016
Status: active
Page Count: 18
ICS Code (Fibres and cables): 33.180.10

Document History

BS EN 60794-5
December 31, 2016
Optical fibre cables Part 5: Sectional specification — Microduct cabling for installation by blowing
A description is not available for this item.
BS EN 60794-5
June 30, 2007
Optical fibre cables - Part 5: Sectional specification - Microduct cabling for installation by blowing
A description is not available for this item.

References

This document references:
IEC TR 62839-1 - Environmental declaration – Part 1: Wires, cables and accessory products – Specific rules
Published by IEC on November 1, 2014
This part of IEC 62839 specifies the PSR (product specific rules) for wires and cables used for communication, data, control and command. This PSR covers the use, installation and end-of-life stages...
This document references:
IEC 60793-1-44 - Optical fibres – Part 1-44: Measurement methods and test procedures – Cut-off wavelength
Published by IEC on April 1, 2011
This part of IEC 60793 establishes uniform requirements for measuring the cut-off wavelength of single-mode optical fibre, thereby assisting in the inspection of fibres and cables for commercial...
This document references:
IEC 60793-1-40 - Optical fibres – Part 1-40: Attenuation measurement methods
Published by IEC on March 1, 2019
This part of IEC 60793 establishes uniform requirements for measuring the attenuation of optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. Four methods...
This document references:
EN IEC 60794-1-1 - Optical fibre cables - Part 1-1: Generic specification - General
Published by CENELEC on July 1, 2023
This part of IEC 60794 applies to optical fibre cables for use with communication equipment and devices employing similar techniques. Electrical properties are specified for optical ground wire...
This document references:
EN IEC 60793-1-40 - Optical fibres - Part 1-40: Attenuation measurement methods
Published by CENELEC on May 1, 2019
This part of IEC 60793 establishes uniform requirements for measuring the attenuation of optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. Four methods...
This document references:
IEC 60793-1-44 - Optical fibres – Part 1-44: Measurement methods and test procedures – Cut-off wavelength
Published by IEC on April 1, 2011
This part of IEC 60793 establishes uniform requirements for measuring the cut-off wavelength of single-mode optical fibre, thereby assisting in the inspection of fibres and cables for commercial...
This document references:
EN IEC 60794-1-1 - Optical fibre cables - Part 1-1: Generic specification - General
Published by CENELEC on July 1, 2023
This part of IEC 60794 applies to optical fibre cables for use with communication equipment and devices employing similar techniques. Electrical properties are specified for optical ground wire...
This document references:
EN IEC 60793-1-40 - Optical fibres - Part 1-40: Attenuation measurement methods
Published by CENELEC on May 1, 2019
This part of IEC 60793 establishes uniform requirements for measuring the attenuation of optical fibre, thereby assisting in the inspection of fibres and cables for commercial purposes. Four methods...
This document is referenced by:
S1932 - Pilot Cables - Copper Cable, Fibre Cable & Accessories
Published by LUL on May 1, 2020
This standard applies to LU their Supplier/contractors and 3rd parties. This standard states the technical requirements for the design, manufacture, type and routine testing of limited fire hazard...
View Less
View All
Advertisement