UNLIMITED FREE
ACCESS TO THE WORLD'S BEST IDEAS

SUBMIT
Already a GlobalSpec user? Log in.

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

Customize Your GlobalSpec Experience

Select Your Free Newsletters

Industry Newsletters

Select Your Free Product Alerts

Finish!
Privacy Policy

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

BSI - BS EN 61914

Cable cleats for electrical installations

inactive
Buy Now
Organization: BSI
Publication Date: 30 September 2009
Status: inactive
Page Count: 32
ICS Code (Conduits for electrical purposes): 29.120.10

Document History

BS EN IEC 61914
January 31, 2022
Cable cleats for electrical installations
A description is not available for this item.
BS EN 61914
March 31, 2016
Cable cleats for electrical installations
A description is not available for this item.
BS EN 61914
September 30, 2009
Cable cleats for electrical installations
A description is not available for this item.

References

This document references:
IEC 61363-1 - Electrical Installations of Ships and Mobile and Fixed offshore Units - Part 1: Procedures for Calculating Short-Circuit Currents in Three-Phase a.c.
Published by IEC on February 1, 1998
Scope and object This International Standard outlines procedures for calculating short-circuit currents that may occur on a marine or offshore a.c. electrical installation. The calculation methods...
This document references:
IEC 60060-1 - High-voltage test techniques – Part 1: General definitions and test requirements
Published by IEC on September 1, 2010
This part of IEC 60060 is applicable to: – dielectric tests with direct voltage; – dielectric tests with alternating voltage; – dielectric tests with impulse voltage; – dielectric tests with...
This document references:
IEC 60695-11-5 - Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
Published by IEC on December 1, 2016
This part of IEC 60695 specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess the fire hazard by a simulation technique. The...
This document references:
IEC 60909-0 - Short-circuit currents in three-phase a.c. systems – Part 0: Calculation of currents
Published by IEC on January 1, 2016
This part of IEC 60909 is applicable to the calculation of short-circuit currents: • in low-voltage three-phase a.c. systems • in high-voltage three-phase a.c. systems operating at a nominal...
This document references:
BS 13/30272930 DC - Draft BS EN ISO 4287:1997/Amd 2 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters - Amendment 2
Published by BSI on April 15, 2013
A description is not available for this item.
This document is referenced by:
BS 7889 - Electric cables - Thermosetting insulated, non-armoured cables with a voltage of 600/1 000 V, for fixed installations
Published by BSI on October 31, 2012
A description is not available for this item.
This document is referenced by:
BS 8573 - Electric cables - Thermosetting insulated, non-armoured cables with a voltage of 600/1 000 V, for fixed installations, and having low emission of smoke and corrosive gases when affected by fire
Published by BSI on October 31, 2012
A description is not available for this item.
This document is referenced by:
NR/L2/SIGELP/27408 - Product Specification for Signalling Power Distribution Cables
Published by NR on March 4, 2017
Cables specified in this standard are intended for use in signalling power distributions systems where the nominal voltage is up to 650 V a.c. and where the electrical systems are either TN or IT....
View Less
View All

Related Products

Searching for related products...

Advertisement