UNLIMITED FREE
ACCESS TO THE WORLD'S BEST IDEAS

SUBMIT
Already a GlobalSpec user? Log in.

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

Customize Your GlobalSpec Experience

Select Your Free Newsletters

Industry Newsletters

Select Your Free Product Alerts

Finish!
Privacy Policy

This is embarrasing...

An error occurred while processing the form. Please try again in a few minutes.

AIA/NAS - NASM122116-122155

INSERT, CRES, HELICAL COIL, COARSE THREAD, 1-1/2 DIA NOMINAL LENGTH

inactive
Buy Now
Organization: AIA/NAS
Publication Date: 30 November 2010
Status: inactive
Page Count: 3

Document History

NASM122116-122155
September 19, 2014
INSERT, CRES, HELICAL COIL, COARSE THREAD, 1-1/2 DIA NOMINAL LENGTH
A description is not available for this item.
NASM122116-122155
November 30, 2010
INSERT, CRES, HELICAL COIL, COARSE THREAD, 1-1/2 DIA NOMINAL LENGTH
A description is not available for this item.
NASM122116-122155
March 1, 1998
Insert, Cres Helical Coil Coarse Thread 1-1/2 Dia Nominal Length
A description is not available for this item.

References

This document references:
ASME B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay)
Published by ASME on January 1, 2019
This Standard is concerned with the geometric irregularities of surfaces. It defines surface texture and its constituents: roughness, waviness, and lay. It also defines parameters for specifying...
This document references:
NASM33537 - INSERT, SCREW THREAD, HELICAL COIL, INCH SERIES, COARSE AND FINE THREAD, STANDARD ASSEMBLY DIMENSIONS FOR
Published by AIA/NAS on January 31, 2017
DESCRIPTION Helical coil inserts are screw thread bushings coiled from diamond shaped cross-section wire. They are screwed into tapped holes to form nominal size internal threads. Inserts are...
This document references:
ASME Y14.36 - Surface Texture Symbols
Published by ASME on November 30, 2018
This Standard establishes methods to designate surface texture controls. It includes symbolic and textual methods for specifying roughness, waviness, and other surface texture information on...
This document references:
ASME Y14.5 - Dimensioning and Tolerancing
Published by ASME on January 1, 2018
INTRODUCTION This Standard establishes symbols, rules, definitions, requirements, defaults, and recommended practices for stating and interpreting dimensioning, tolerancing, and related requirements...
This document references:
MIL-S-7742 - SCREW THREADS, STANDARD, OPTIMUM SELECTED SERIES: GENERAL SPECIFICATION FOR
Published by NPFC on July 25, 1991
This specification covers the requirements for a selected series of standard Unified and Unified Miniature screw threads, classes 3A and 3B of FED-STD-H28/2 and FED-STD-H28/5 for general aerospace...
This document is referenced by:
DSCC-DWG-84103 - HOLDER, ELECTRICAL CARD, WEDGE RETAINER,3-PIECE, SCREW ACTUATED
Published by DOD on December 4, 2013
This drawing describes the requirements for a family of metal card holders for use with printed circuit boards and circuit card assemblies in moderate shock and vibration environments.
This document is referenced by:
DESC-DWG-89064 - HOLDER, ELECTRICAL CARD, WEDGE RETAINER, 5 PIECE, .225 INCH BY .225 INCH AND .225 INCH BY .260 INCH BODY SIZE
Published by DOD on April 9, 2018
This drawing describes the requirements for a family of 5 wedge metal card-retainers intended to hold circuit card assemblies or printed wiring assemblies in their installed positions.
View Less
View All
Advertisement