loading
DATA EMITTERS & SENSORS - DATA EMITTERS & SENSORS
DATA
A description is not available for this item.
IEEE EMC/EMI - EMC/EMI: SELECTED READINGS
IEEE
A description is not available for this item.
ASTM E1419/E1419M-26 - Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
May 1, 2026 - ASTM International

5.1 Because of safety considerations, regulatory agencies (for example, U.S. Department of Transportation) require periodic examinations of vessels used in transportation of industrial gases (see Section 49, Code of Federal Regulations). The AE examination has become accepted as an alternative to...

ASTM E2907/E2907M-25 - Standard Practice for Examination of Paper Machine Rolls Using Acoustic Emission from Crack Face Rubbing
September 1, 2025 - ASTM International

5.1 Paper machine rolls can range in size from 2.4?m to 9 m [8?ft to 30 ft] long, with a shell thickness of from 12.5?mm to 75 mm [0.5?in. to 3 in.,] and 300?mm to 1200 mm [12?in. to 48 in.] diameter. Depending on purpose, paper machine rolls can weigh as little as 60 000 kg [13 000 lb] to as much...

ASTM E1930/E1930M-25 - Standard Practice for Examination of Liquid-Filled Atmospheric and Low-Pressure Metal Storage Tanks Using Acoustic Emission
September 1, 2025 - ASTM International

5.1 General-This procedure is used for evaluation of the structural integrity of atmospheric storage tanks. The AE method can detect flaws which are in locations that are stressed during pressurization. Such locations include the tank wall, welds attaching pads to the tank, nozzle attachments, and...

ASTM E1888/E1888M-17(2025) - Standard Practice for Acoustic Emission Examination of Pressurized Containers Made of Fiberglass Reinforced Plastic with Balsa Wood Cores
July 1, 2025 - ASTM International

4.1 This practice does not rely on absolute quantities of AE parameters. It relies on trends of cumulative AE counts that are measured during a specified sequence of loading cycles. This practice includes an example of examination settings and acceptance criteria as a nonmandatory appendix. 4.2...

ASTM B734-97(2023) - Standard Specification for Electrodeposited Copper for Engineering Uses
November 1, 2023 - ASTM International

1.1 This specification covers requirements for electrodeposited coatings of copper used for engineering purposes. Examples include surface hardening, heat treatment stop-off, as an underplate for other engineering coatings, for electromagnetic interferences (EMI) shielding in electronic...

AS81582C - Connectors, Electrical, Bayonet Coupling, Environment Resisting, Umbilical, General Specification For
October 3, 2023 - SAE International

This specification covers environment-resisting, quick disconnect, EMI/RFI shielded and non-shielded umbilical, electric connectors and adapter assemblies with removable crimp or nonremovable solder-type contacts and accessories. Connectors are rated for operation from -55 °C (-67 °F) to 200...

AIR6236A - In-House Verification of EMI Test Equipment
June 24, 2022 - SAE International

This AIR provides guidance to the EMI test facility on how to check performance of the following types of EMI test equipment: Current probe Line Impedance Stabilization Network (LISN) Directional coupler Attenuator Cable loss Low noise preamplifier Rod antenna base Passive antennas...

ARP1705C - Coaxial Test Procedure to Measure the RF Shielding Characteristics of EMI Gasket Materials
June 24, 2022 - SAE International

The purpose of this procedure is to establish a technique for reliably and repeatedly measuring the RF shielding characteristics of EMI gasket materials and EMI gaskets against various joint surfaces. The procedure is also used to test the reliability of the gasketed joint...

ARP6248 - Stripline Test Method to Characterize the Shielding Effectiveness of Conductive EMI Gaskets up to 40 GHz
January 21, 2022 - SAE International

The purpose of this procedure is to establish a technique for reliably and repeatedly measuring the RF shielding characteristics of EMI conductive gasket materials and EMI conductive gaskets. Depending on the materials used for the construction of the measuring setup, the EMI...

AIR5128A - Electrical Bonding of Aircraft Fuel Systems
October 4, 2022 - SAE International

This SAE Aerospace Information Report (AIR) is limited to the subject of aircraft fuel systems and the questions concerning the requirements for electrical bonding of the various components of the system as related to Static Electric Charges, Fault Current, Electromagnetic Interference (EMI)...

DSCC-DWG-07004 - FILTER, EMI, HYBRID, 28V dc
March 24, 2021 - DOD

Scope. This drawing describes the requirements for hybrid microcircuit electromagnetic interference (EMI) suppression filters to be processed in accordance with MIL-PRF-38534. Two product assurance classes consisting of class H (military high reliability) and class K (space application) and...

J1742_202208 - Connections for High Voltage On-Board Vehicle Electrical Wiring Harnesses - Test Methods and General Performance Requirements
August 5, 2022 - SAE International

Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in high power road vehicle applications that...

DESC-DWG-95004 - FILTER, EMI, HYBRID
June 9, 2020 - DOD

Scope. This drawing describes the requirements for hybrid microcircuit electromagnetic interference (EMI) suppression filters to be processed in accordance with MIL-PRF-38534. Two product assurance classes consisting of class H (military high reliability) and class K (space application) and...

AIR5271A - A Guideline for Application of High-Density Fiber Optic Interconnects to Aerospace Platforms
July 8, 2022 - SAE International

This SAE Aerospace Information Report (AIR5271) covers the basic attributes of a second-generation robust, reliable high-density fiber optic interconnect system for aerospace applications. The intent is to take advantage of recent commercial developments in materials, components and manufacturing...

J1939/14_202204 - Physical Layer, 500 kbit/s
April 5, 2022 - SAE International

This document defines a physical layer having a higher bandwidth capacity than other physical layers defined for SAE J1939. Newer transceiver technologies are utilized to minimize EMI. CAN controllers are now available which support the flexible data rate frame format. These controllers,...

Advertisement