1.1 These test methods describe a procedure for determining the amount of volatile matter of any kind that is driven off from a test specimen under a specific set of temperature and time conditions. These test methods determine only the mass of material lost, not its identity. 1.2 These test...
1.1 This practice covers procedures commonly used in the paint industry to formulate paints and coating materials. It describes procedures for calculating formulation values for weight solids, volume solids, solvent content, volatile organic compound (VOC) content, hazardous air pollutant...
1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs)....
5.1 This test method is designed specifically for emulsions of pesticide emulsifiable concentrates. 5.2 This test method provides information on the absorption/adsorptio
1.1 This guide provides procedures for using a reference material with a known emission rate of a volatile organic compound (VOC) to estimate the bias associated with a VOC emission chamber test. 1.2 This guide may be used to assess measurements of VOC emissions conducted in a...
1.1 These test methods cover the determination of the transfer efficiency of spray-applied coatings under general plant conditions. Transfer efficiency is the ratio of paint solids deposited to the total paint solids used during the application process, expressed as a percent. 1.2 The transfer...
5.1 In using the methods of Practice D3960 to measure the VOC content of coatings, precision tends to be poor for waterborne coatings because the VOC weight fraction is determined indirectly. The present method first identifies and then quantifies the individual VOCs directly....
4.1 This test method determines the volatile organic content of an electrical insulating varnish. It utilizes a procedure where dishes containing a known amount of varnish are baked and the amount of volatile organic compound is measured. Calculations are performed to express this in g/L or lb/gal....
1.1 This specification provides requirements for membrane-forming liquids suitable for use as curing compounds and sealers on freshly placed concrete and as sealers on hardened concrete. These membranes have special properties, such as, alkali resistance, acid resistance, adhesion-promoting..
5.1 This practice discusses applicable ASTM test methods used in the determination of the VOC content of paints and related coatings and provides equations for calculating the VOC content expressed as the mass of VOC: (1) per unit volume of coating less water and exempt...
5.1 Historically, portable air cleaners were designed to remove airborne particles. More recently air cleaners have sought to also remove chemicals or airborne pathogens, or both. Concurrent with market development, there have been a range of test methods created to examine the removal or...
5.1 Historically, portable air cleaners were designed to remove airborne particles. More recently air cleaners have sought to also remove chemicals or airborne pathogens, or both. Concurrent with market development, there have been a range of test methods created to examine the removal or...
1.1 This practice describes procedures for testing the emissions of volatile organic compounds (VOCs), formaldehyde, and other carbonyl compounds, from alkyd paint, latex paint, primer, and other architectural coating samples using a small-scale environmental chamber test facility. 1.2 This...
1.1 This guide is intended to aid in the selection of the proper ASTM standard for determining the volatile and nonvolatile content of paint and related coatings. Note 1: Test methods for determining the composition of the volatile fraction are not covered by this guide. 1.2 The standards included...
1.1 This specification covers liquid membrane-forming compounds suitable for application to concrete surfaces to reduce the loss of water during the early-hardening period. White-pigmented membrane-forming compounds serve the additional purpose of reducing the temperature rise in concrete exposed...
5.1 VOCs emitted from materials/products affect indoor air quality (IAQ) in buildings. To determine the impact of these emissions on IAQ, it is necessary to know their emission rates over time. This practice provides guidelines for using a full-scale environmental chamber for testing large...
5.1 Manufacturers of carpet need to monitor emissions of VOCs to assess the environmental impact of their products indoors. These results are also used to demonstrate compliance with VOC emission limits for individual VOCs. 5.2 These data are also used to understand which...
4.1 Objectives-The use of small chambers to evaluate VOC emissions from indoor materials has several objectives: 4.1.1 Develop techniques for screening of products for VOC emissions; 4.1.2 Determine the effect of environmental variables (that is, temperature, humidity, air speed, and...
1.1 This test method is for the determination of the weight percent of individual volatile organic compounds in low VOC air-dry coatings (Note 1). 1.2 This test method may be used for the analysis of coatings containing silanes, siloxanes, and silane-siloxane blends. 1.3 This test method is...
1.1 This specification covers minimum material performance requirements and laboratory test procedures for non-reinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are: 1.1.1 Impact...
Narrow Your Results