4.1 Safety factors must be addressed and incorporated into the work to protect the workers and the public, and construction activities may need to be altered accordingly. Engineering and construction costs are a part of the analysis. 4.2 Access rights to the work should be considered in the...
4.1 This guide is intended to provide information and guidance for designers, specifiers, manufacturers, contractors and users that are considering the use of prefabricated masonry elements. This guide identifies situations when prefabrication could be considered where other prefabricated systems...
1.1 These practices describe laboratory procedures for preparing an oil-based ink resin solution in a high-boiling solvent using four pieces of lab equipment: (1) A hot oil bath (Sections 4 to 11), (2) A stirrer/hot plate (Sections 12 to 16), (3) An industrial blender (Sections 17 to 22), and (4) A...
1.1 Laser profiling is a non-contact inspection method used to create a pipe wall profile and internal measurement using a standard CCTV pipe inspection system, 360° laser light projector, a measurement by means of infrared sensors and geometrical profiling software. This practice covers the...
4.1 The recommended measurement procedures described in this guide are intended to provide performance-related measurements that can be reproduced under the specified test conditions using commercially available test instrumentation. These measurements indicate capabilities of sections of the...
5.1 The techniques described provide for the measurement of change in length of a fastener. Such measurements are made from one end of the specimen without requiring access to the rear surface. 5.2 The Ultrasonic Pulse Echo technique is used to monitor changes in length of fasteners and as a...
1.1 This practice covers the procedure for the post installation verification and acceptance of buried pipe deformation using a visible rotating laser light diode(s), a pipeline and conduit inspection analog or digital CCTV camera system and image processing software. The combination CCTV pipe...
4.1 The design and operation of a self-contained irradiator should ensure that reproducible absorbed doses are obtained when the same irradiation parameters are used. Dosimetry is performed to determine the relationship between the irradiation parameters and the absorbed dose. 4.1.1 For most...
1.1 There is an ongoing need to maintain, preserve, and standardize microbiological cultures for research. This guide is focused on three parts of microbe preservation: 1.1.1 Process Description-This includes detailed microbe characterization data and documentation of microbial passaging,...
4.1 The hardness of a material is a defined quantity having many scales and being dependent on the way the test is performed. In order to avoid the creation of a new method involving a new hardness scale, the UCI method converts into common hardness values, for example, HV, HRC, etc. 4.2 The UCI...
3.1 This specification provides designers and manufacturers of electric propulsion for light sport aircraft design references and criteria to use in designing and manufacturing EPUs. 3.2 Declaration of compliance is based on testing and documentation during the design, ground testing and flight...
5.1 This guide presents options for a systematic assessment of fungal growth in buildings. 5.2 This guide allows for site-specific flexibility and professional judgment in the choice of assessment procedures. It may not be necessary to perform in its entirety the basic assessment presented below to...
5.1 To design relevant performance metrics and methods for characterizing grasp-type end-effectors, this practice helps to understand the contextual or application-specific
5.1 Flaws that are made during manufacturing or that occur during service of a component have the potential to cause the component to fail. NDT methods such as described in Practice E2700 are intended to locate flaws that have the potential to result in component failure. Since not all flaws will...
4.1 Management of asbestos-containing materials in buildings and facilities requires knowledge of the location, type, quantity, and condition of the material. The more complete and accurate the information available, the more appropriate and cost-effective are the control measures used to reduce...
5.1 Phased array ultrasonic testing (PAUT) is an advanced examination technique used for enhanced flaw detection, sizing, and imaging as compared to conventional UT employing single-element transducers. PAUT utilizes multi-element (array) probes in which groups of elements are pulsed with...
Narrow Your Results