3.1 These test methods are used to evaluate the properties of self-adhesive modified bituminous membranes. The results determine compliance with the applicable specifications, or they can be used for comparative analysis. 3.2 The test methods apply to "as manufactured" material and may not...
6.1 Adhesives used in the repair of sandwich panels for durable, rigidwall, relocatable structures must have a combination of mechanical property levels and environmental resistance that will ensure long-term durability of the adhesive bonds when exposed to severe climatic exposures....
1.1 This practice covers sample preparation temperatures, test parameters, and specimen exposure conditions that are applicable when Test Method D5405/D5405M is used for conducting time-to-failure (creep-rupture) tests of adhesive joints fabricated from ethylene-propylene-d
4.1 The formation of reproducible, durable-adhesive bonds in structural units requires great care in the selection of materials, the preparation of the surfaces of the parts to be bonded, and the performance of the steps in the bonding process. Experience has shown that adhesive...
1.1 This classification covers silicone adhesives and sealants intended for but not limited to sealing and retaining metallic and nonmetallic component assemblies in transportation applications. The materials cure to an elastomeric state by their specified cure system and mechanism. Note 1:...
This specification covers the requirements for an adhesive which is intended for use in bonding pre-fabricated acoustical materials to the inside walls and ceilings of rooms in buildings. This adhesive is required to maintain a specific tensile adhesion or bond strength for a long...
1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: 1.1.1 Class 1-Non-elastomeric backings made from materials such as: Paper, flat or creped, Fabric, uncoated or coated,...
4.1 Resin Identification Codes are used solely to identify the plastic resin used in a manufactured article. The intended manufactured articles include, but are not limited to, packaging. 4.1.1 Fig. 1 and Table 1 present the appropriate information on the way the RIC is to be incorporated onto the...
1.1 This test method covers the measurement of mass per unit area of machine-made woven, knitted, and tufted pile yarn floor covering both before and after an adhesive-back coating application. 1.2 This test method encompasses three techniques for determination of mass per unit area as...
5.1 This guide is designed to assist a practitioner in the selection of appropriate sample preparation methods for the analysis, comparison, and identification of pressure sensitive adhesive (PSA) tapes. 5.2 It is not the intent of this guide to present comprehensive theories and methods of...
5.1 This guide is designed to assist a practitioner in the selection of appropriate sample preparation methods for the analysis, comparison, and identification of pressure sensitive adhesive (PSA) tapes. 5.2 It is not the intent of this guide to present comprehensive theories and methods of...
5.1 An important factor affecting the performance of joints of nonbituminous membranes is their ability to remain bonded over the membrane's expected service life. Time-to-failure tests provide a means of characterizing the behavior of joints under constant load over time. 5.2 Creep is a sensitive...
5.1 The ability of a substrate surface to readily absorb water is a key indicator in determining how to correctly install many types of flooring adhesives, primers, self-leveling underlayments, and other products. Several flooring industry publications such as CRI's Carpet Installation...
1.1 This practice is intended to provide accepted installation procedures for thin brick units in adhered veneer systems in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of clay and shale thin brick...
1.1 This guide provides information regarding masonry elements constructed at locations other than in-place. Prefabrication may occur on the jobsite or offsite and transported to the jobsite. This guide covers lintels, arches, sloped sills, spandrels, soffits, wall panels, and other masonry...
1.1 This practice covers the installation and preparation of the thick poured lightweight cellular concrete underlayments over wood structural panel subfloors in commercial structures or over concrete floors in commercial structures and the preparation of the thick poured lightweight cellular...
1.1 This specification covers the minimum requirements for, and methods of, application of gypsum veneer base for gypsum veneer plasters. 1.2 Gypsum veneer base shall not be used as a base for direct adhesive application of ceramic, metal, or plastic tile in areas exposed to abnormal...
1.1 This fire-test-response test method covers a procedure for measuring fire properties associated with flammable behavior of surface finishes used on noncombustible substrates (Note 1). In particular, these include surface finishes intended for use as surfacing materials and ceiling veneers...
Narrow Your Results