5.1 The measured mean bulk density of a coal stockpile is used with a measurement of the stockpile volume per Test Method D6172/D6172M. Procedures to determine the quantity of stockpiled coal. This measure of quantity is often used as a reference value for adjusting inventory records.
1.1 This practice is used to calculate the mass (commonly expressed in tons) of coal in a storage pile using the volume of the stockpile by Test Method D6172/D6172M and the density of the coal determined by Test Method D6347/D6347M. 1.2 This practice is applicable to all ranks of coal. 1.3 The user...
3.1 Synthetic plasticizers are primarily esters and they are used with the more polar elastomers such as CR or NBR to improve processing, adjust hardness, and improve low temperature properties. These esters may be either monomeric or polymeric and are derived from many different organic...
5.1 Dynamic mechanical analysis monitors changes in the viscoelastic properties (that is, storage modulus, loss modulus, tangent angle delta) of a material as a function of temperature and frequency, providing a means to quantify these changes. In many cases, the value to be assigned is the...
1.1 This test method describes the use of the M.I.T.-type folding apparatus for determining folding endurance of paper and plastics film. The M.I.T. tester can be adjusted for samples of any thickness; however, if the outer layers thicker than about 0.25 mm (0.01 in.) rupture during the...
1.1 This test method covers the determination of mold growth resistance of Wet Blue and Wet White subject to storage and shipping requirements and intended for use in leather manufacturing. This test method may not be suitable to evaluate fungicides that are inactivated by proteins. This includes...
5.1 The determination of pile thickness of multilevel pile yarn floor covering is useful in quality and cost control during manufacture of pile yarn floor covering. The appearance and performance may be affected by changes in pile thickness of pile yarn floor coverings. This test method is...
5.1 This test method can be useful in characterizing and comparing shrinkage properties of both primary and secondary backing fabrics. This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between-laboratory precision are acceptable,...
1.1 This practice covers bactericidal claims for non-food-contact antimicrobial surfaces. 1.2 This practice is applicable to a wide range of surfaces, including nonporous, semi-porous, and hydrophobic surfaces. 1.3 This practice is also applicable for determining the efficacy of additives...
4.1 The test method was developed for determining the fracture resistance of asphalt mixtures. The fracture resistance can help differentiate asphalt mixtures whose service life might be compromised by cracking. The test method is generally valid for specimens that are tested at temperatures of...
4.1 Physical constants of paints and coatings are required in all aspects of their formulation, manufacture and use. This practice demonstrates standard methods agreed upon for calculating formulation values for some of these physical constants. The calculations are the same for either metric or...
4.1 In 2014, the U.S. EPA published the final rules adding renewable fuel pathways under the RFS Program. The rules qualified kernel fiber as a cellulosic feedstock meeting the 60?% greenhouse gas (GHG) reduction and qualifies for the generation of D3 RINs. These rules allow for two approaches for...
5.1 This test method is based on Test Method F903 for measuring resistance of chemical protective clothing materials to penetration by liquids. This test method is normally used to evaluate specimens from individual finished items of protective clothing and individual samples of materials that are...
1.1 This guide covers the establishment and use of an ASTM-recommended file that consists of a set of nuclear data cross sections, uncertainty data, and associated product decay data for analysis of single or multiple sensor measurements in neutron fields related to light water reactor (LWR)...
4.1 This practice is intended to be used as a guide by those involved in the design of asphalt surface treatments. It covers typical application rates for the various types of surface treatments and covers aggregate sizes and recommended grades of asphaltic material for both hot and cool weather...
5.1 This test method gives a standard procedure for determining structural performance under uniform static air pressure difference. This typically is intended to represent the effects of wind loads on exterior building surface elements. The actual loading on building surfaces is quite complex,...
1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to the IR...
This specification covers the establishment of the minimum requirements for the design, testing, and quality assurance of fixed-pitch or ground adjustable propellers for light sport aircraft. The propeller may not have design features that have been shown to be hazardous or unreliable unless...
5.1 The ability of a substrate surface to readily absorb water is a key indicator in determining how to correctly install many types of flooring adhesives, primers, self-leveling underlayments, and other products. Several flooring industry publications such as CRI's Carpet Installation Standard,...
1.1 This practice covers a procedure for calculating and interpreting the internal rate of return (IRR) and adjusted internal rate of return (AIRR) measures in the evaluation of building designs, systems, and equipment. 1.2 The values stated in inch-pound units are to be regarded as standard...