5.1 This practice may be used to continuously demonstrate the proficiency of analytical measurement systems that are used for establishing and ensuring the quality of petroleum and petroleum products. 5.2 Data accrued, using the techniques included in this practice, provide the ability to...
1.1 This is a compilation of terms commonly used in analytical chemistry for metals, ores, and related materials. Terms that are generally understood or defined adequately in other readily available sources are either not included or their sources are identified. 1.2 A definition is a single...
1.1 This practice covers a standard procedure for the cooling of analytical solutions such as those prepared in Practices D4901, D4905, or D6405. The tannin analysis results for an analytical solution are to some extent dependent on the conditions of the cooling of that solution. 1.2...
5.1 This practice may be used to continuously demonstrate the proficiency of analytical measurement systems that are used for establishing and ensuring the quality of petroleum and petroleum products. 5.2 Data accrued, using the techniques included in this practice, provide the ability to...
1.1 This test method provides procedures for validating temperature and enthalpy measurements of differential scanning calorimeters (DSC) and analytical methods based upon the measurement of temperature or enthalpy (or heat), or both, by DSC. Performance parameters determined include...
4.1 Because of the loss of life in fires from inhalation of fire gases, much attention has been focused on the analyses of these species. Analysis has involved several new or modified methods, since common analytical techniques have often proven to be inappropriate for the combinations of...
4.1 Physical constants of paints and coatings are required in all aspects of their formulation, manufacture and use. This practice demonstrates standard methods agreed upon for calculating formulation values for some of these physical constants. The calculations are the same for either metric or...
1.1 These test methods cover the chemical analyses usually required for sodium chloride. 1.2 The analytical procedures appear in the following sections: Section Sample Preparation ?5 to? 9 Moisture 10 to 17 Water Insolubles 18 to 26 Calcium and Magnesium 27 to 34 Sulfate 35 to 42 Reporting...
1.1 This test method covers a procedure for the evaporating and drying of the 100 mL portions of analytical solution obtained in the methods for vegetable tannin analysis, so that consistent results may be obtained for the determination of total solids, soluble solids, and non-tannins in the...
1.1 These test methods cover procedures for the chemical and mass spectrometric analysis of nuclear-grade gadolinium oxide powders to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Carbon by Direct Combustion-Thermal..
5.1 The microactivity test provides data to assess the relative performance of FCC catalysts. Because results are affected by catalyst pretreatment, feedstock characteristics, test equipment, and operating parameters, adherence to this test method is a prerequisite for correct interpretation of...
1.1 These test methods cover procedures for the chemical analysis of metallic zinc powder in the form commercially known as zinc dust for use as a pigment in paints. 1.2 The analytical procedures appear in the following order: Sections Moisture and Other Volatile Matter 7 Coarse Particles 8...
1.1 This terminology covers those terms recommended by the International Union of Pure and Applied Chemistry (IUPAC), and is intended to provide guidance in the use of ion-selective electrodes for analytical measurement of species in water, wastewater, and brines. 1.2 This international...
5.1 This test method provides a simple approach for determining the transmission properties of film membranes and sheeting over a range of permeability exceeding four orders of magnitude. This test method is described here to measure the permeability of films used in soil fumigation, but it is also...
6.1 This guide is designed to assist in the selection and organization of an analytical scheme for evaluating paints and coatings. The size and condition of the sample(s) will influence the selected analytical scheme. The evaluation and interpretation of the data for each technique is...
1.1 This guide covers products with chemesthetic heat sensations where the perception is derived from chemical stimulation of the trigeminal nerve in the nasal or oral cavity and are colloquially described as spicy, pungent, acrid, irritation, or burn. However, as there are no agreed-upon...
1.1 This test method describes the testing, analytical, and characterization methods for evaluating the long-term fretting corrosion performance of the bore and cone interface of the head and stem junction of modular hip implants subjected to cyclic loading in a corrosive environment (1-5)....
4.1 This guide deals with the difficult problem of benchmarking neutron transport calculations carried out to determine fluences for plant-specific reactor geometries. The calculations are necessary for fluence determination in locations important for material radiation damage estimation and which...
Narrow Your Results