This guide provides information on the deposition of engineering chromium by electroplating. This is sometimes called "functional" or "hard" chromium and is usually applied directly to the basis metal and is usually thicker than decorative deposits. This guide is not intended as a standardized...
3.1 Water-blast cleaning with (SSPC-TR2/NACE 6G 198; SSPC-SP 5 (WAB)/NACE WAB-1; SSPC-SP 10 (WAB)/NACE WAB-2; SSPC-SP 6 (WAB)/NACE WAB-3; SSPC-SP 14 (WAB)/NACE WAB-8); SSPC-SP 7 (WAB)/NACE WAB-4 or without, (SSPC-SP WJ-1/NACE WJ-1; SSPC-SP WJ-2/NACE WJ-2; SSPC-SP WJ-3/NACE WJ-3; SSPC-SP WJ-4/NACE...
5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...
5.1 This technique is applicable to dry paint films in a variety of forms including the intact dry paint film surface, a notched or other angular cut surface that exposes a cross section of all paint layers, a paint chip, and ground paint film. 5.2 The response of the spot test method varies...
1.1 This test method covers the determination of the apparent density of core samples from manufactured articles of anode and cathode carbon used by the aluminum industry in the production of aluminum. 1.2 The values stated in SI units are to be regarded as standard. The values given in...
This practice serves as a guide for the preparation of nickel alloy substrates that shall undergo electroplating processes involving adherent nickel electrodeposits. Surface cleaning may be done either by degreasing (including vapor degreasing, solvent wash, emulsion cleaning, or soak cleaning), or...
This guide outlines the standard procedure for establishing and maintaining a preparatory cycle for electroplating on high carbon steel producing minimal hydrogen embrittlement and maximal adhesion of the electrodeposited metal. The reagents needed for this method are technical grade hydrochloric...
1.1 This practice covers the evaluation of atmospheric galvanic corrosion of any anodic material that can be made into a wire when in contact with a cathodic material that can be made into a threaded rod. 1.2 When certain materials are used for the anode and cathode, this practice has...
4.1 Hexavalent chromium salts are used extensively in metal finishing and plating applications, in anodizing aluminum, and in the manufacture of paints, dyes, explosives, and ceramics. Trivalent chromium salts are used as mordants in textile dyeing, in the ceramic and glass industry, in the...
5.1 This practice is intended for the digestion of lead in dust wipe samples collected during various lead hazard activities performed in and around buildings and related structures. 5.2 This practice is also intended for the digestion of lead in dust wipe samples collected during and after...
This specification covers the standard requirements for magnesium alloy anodes in the form of cast and extruded shapes for use in cathodic protection. Materials shall adhere to specified chemical composition requirements, the samples for analysis of which shall be taken either from the...
1.1 These test methods cover the determination of dissolved and total recoverable cadmium in water and wastewater by atomic-absorption spectrophotometry and differential pulse anodic stripping voltammetry.2 Section 44 on Quality Control pertains to these test methods. Four test methods are...
1.1 This specification covers requirements for electrolytically formed porous oxide coatings on aluminum and aluminum alloy parts in which appearance, abrasion resistance, electrical properties, and protection against corrosion are important. Nonporous, barrier layer anodic coatings used for...
1.1 This guide describes the requirements for phosphoric acid anodizing of aluminum and its alloys for structural adhesive bonding. 1.2 The procedure included herein is based on the commercial practice of numerous agencies and organizations. The method may be revised or supplemented, as...
1.1 This practice describes a procedure for calibrating the electron binding-energy (BE) scale of an X-ray photoelectron spectrometer that is to be used for performing spectroscopic analysis of photoelectrons excited by unmonochromated aluminum or magnesium Ka X-rays or by monochromated aluminum Ka...
1.1 This test method covers the determination of the resistance of organic coatings to abrasion produced by the Taber Abraser on coatings applied to a plane, rigid surface, such as a metal panel. 1.2 Units-The values stated in SI units are to be regarded as the standard, with the exception of mils...
5.1 The electrical resistivity of anode and cathode carbon material is important for efficient aluminum cell operation. It is a quality parameter that determines the suitability of an anode/cathode for operation in an aluminum cell. 5.2 The electrical resistivity may be selected as a...
1.1 This test method covers general test procedures and evaluation criteria for the corrosion resistance of new and reusable surgical instruments fabricated from stainless steel alloys such as but not limited to those listed in Specification F899. 1.2 Instruments containing stainless steel...
1.1 This test method covers the determination of the coefficient of linear thermal expansion (CTE) for carbon anodes and cathodes used in the aluminum industry, in baked form, by use of a vitreous silica dilatometer. 1.2 The applicable temperature range for this test method for research...
This guide covers procedures for preparing various wrought metal surfaces for adhesive bonding. Surface treatment methods involving both mechanical and chemical techniques are included for aluminum alloys, stainless steel, carbon steel, titanium alloys, magnesium alloys, and copper and copper...
Narrow Your Results