loading
IEEE MOBILE HDBK - THE MOBILE COMMUNICATIONS HANDBOOK
IEEE
A description is not available for this item.
ASME B30.5 - Mobile and Locomotive Cranes
August 6, 2018 - ASME

Within the general scope defined in Section I of the B30 Standard Introduction, American National Standard B30.5 applies to crawler cranes, locomotive cranes, wheelmounted cranes, and any variations thereof that retain the same fundamental characteristics. The scope...

ANSI B30.5 - MOBILE AND LOCOMOTIVE CRANES
ASME
A description is not available for this item.
AWWA B305 - Anhydrous Ammonia
January 24, 2015 - AWWA

This standard describes the use of anhydrous ammonia for water supply service application. Anhydrous ammonia is expressed by the formula NH3. Anhydrous means free from water. Purpose The purpose of this standard is to provide the minimum requirements for anhydrous ammonia, including physical,...

AIA B305 - Architect's Qualification Statement
January 1, 1993 - AIA/ARCH
A description is not available for this item.
ASME B30.5 SPANISH - Grúas Ferroviarias y Móviles
December 31, 2014 - ASME
A description is not available for this item.
ISO HDBK CRANES V1 - CRANES - VOLUME 1: TERMINOLOGY AND GRAPHIC SYMBOLS
ISO
A description is not available for this item.
ISO HDBK CRANES V2 - CRANES - VOLUME 2: DESIGN REQUIREMENTS, ACCESSORIES
ISO
A description is not available for this item.
CRANE TP 410 METRIC - Flow of Fluids: Through Valves, Fittings, and Pipe
FOF

Originally developed in 1942, the CRANE Technical Paper No.410 (TP-410) is the quintessential guide to understanding the flow of fluidthrough valves, pipes, and fittings. The manual is intended for DesignEngineers, Plant Engineers, Facility Managers, Maintenance Technicians,Mechanics,...

CRANE PIPING SYS FUND - Piping System Fundamentals: The Complete Guide to Gaining a Clear Picture of Your Piping System
FOF

PipingSystem Fundamentals is a complete guide to gaining a clear picture of yourpiping system. This manual takes an extensive look at the main conditionsaffecting the operation of a piping system, describing the interaction betweenpumps, compressors, pipelines, control valves, and other...

CRANE TP 410 US - FLOW OF FLUIDS THOUGH VALVES, FITTINGS, AND PIPE
FOF
A description is not available for this item.
ASTM B940-05(2026) - Standard Practice for Testing Non-Chromate Coatings on Zinc and Cadmium Surfaces
May 1, 2026 - ASTM International

4.1 This practice is applicable to non-chromate coatings that are colorless, colored, electrochemically applied or non-electrochemically applied. The zinc or cadmium, or both, may be electrodeposited, mechanically deposited, hot-dipped, rolled, or in the form of castings. 4.2 Because of variables...

ASTM B57-27 - Specification for Copper-Alloy Condenser Tube Plates (Withdrawn 1941)
January 1, 2027 - ASTM International
A description is not available for this item.
ASTM D6347/D6347M-05(2026) - Standard Test Method for Determination of Bulk Density of Coal Using Nuclear Backscatter Depth Density Methods
July 15, 2026 - ASTM International

5.1 The measured mean bulk density of a coal stockpile is used with a measurement of the stockpile volume per Test Method D6172/D6172M. Procedures to determine the quantity of stockpiled coal. This measure of quantity is often used as a reference value for adjusting inventory records.

ASTM D6542-05(2026) - Standard Practice for Tonnage Calculation of Coal in a Stockpile
July 15, 2026 - ASTM International

4.1 The physical inventory of tons of coal in a stockpile, as calculated by this practice, may be used for accounting and tax purposes. 4.2 The inventory results may be compared to other estimates of the inventory, such as: 4.2.1 Tons from a previous inventory less tons shipped or consumed. 4.2.2...

ASTM B163-26 - Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
July 1, 2026 - ASTM International

1.1 This specification covers seamless tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service. 1.2 This specification covers outside diameter and average wall, or outside diameter and minimum wall tube. 1.2.1 The sizes covered by this specification...

Advertisement