loading
ASTM D6752/D6752M-26 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
August 1, 2026 - ASTM International

4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...

ASTM C1072-26 - Standard Test Methods for Measurement of Masonry Flexural Bond Strength
June 1, 2026 - ASTM International

1.1 These test methods evaluate the flexural bond strength, normal to the bed joints, of masonry built of manufactured masonry units. Sampling and testing procedures are referenced, and terms are defined. Three different specimen fabrication methods are specified, each for a different purpose: 1.1...

ASTM D7063/D7063M-26 - Standard Test Method for Effective Porosity and Effective Air Voids of Compacted Asphalt Mixture Samples
May 1, 2026 - ASTM International

4.1 In this test method, a compacted sample is vacuum sealed inside a plastic bag. The density of the sample, SG1, is calculated using a water displacement method, with the sample sealed. With the sample still in water, the bag is cut open. Since the sample is under vacuum and the air...

ASTM E2969-18(2026) - Standard Test Methods for Transverse Load Tests on Panels Used in Wall Construction
April 1, 2026 - ASTM International

1.1 These test methods cover transverse load testing to determine the structural properties of wall segments. 1.2 These test methods serve to evaluate the performance of wall panels subject to transverse bending loads applied perpendicular to the plane of the wall. The tests are conducted on...

ASTM D7859-26 - Standard Practice for Spraying, Sampling, Packaging, and Test Specimen Preparation of Spray Polyurethane Foam (SPF) Insulation for Testing of Emissions Using Environmental Chambers
April 1, 2026 - ASTM International

1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs). These...

ASTM D1777-26 - Standard Test Method for Thickness of Textile Materials
January 1, 2026 - ASTM International

1.1 This test method covers the measurement of the thickness of most textile materials. 1.2 This test method applies to most fabrics including woven fabrics, air bag fabrics, blankets, napped fabrics, knitted fabrics, layered fabrics, and pile fabrics. The fabrics may be untreated, heavily...

ASTM D5817-25 - Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing
December 15, 2025 - ASTM International

4.1 Several test methods for carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice provides...

ASTM D7063/D7063M-25 - Standard Test Method for Effective Porosity and Effective Air Voids of Compacted Asphalt Mixture Samples
November 1, 2025 - ASTM International

4.1 In this test method, a compacted sample is vacuum sealed inside a plastic bag. The density of the sample, SG1, is calculated using a water displacement method, with the sample sealed. With the sample still in water, the bag is cut open. Since the sample is under vacuum and the air...

ASTM D3939/D3939M-26 - Standard Test Method for Snagging Resistance of Fabrics (Mace)
January 1, 2026 - ASTM International

5.1 This test method is not considered satisfactory for acceptance testing of commercial shipments of fabrics because the between-laboratory precision of the test method is poor (see 15.1). 5.1.1 If there are differences of practical significance between reported test results for two laboratories...

ASTM D1424-25 - Standard Test Method for Tearing Strength of Fabrics by Falling-Pendulum (Elmendorf-Type) Apparatus
November 1, 2025 - ASTM International

1.1 This test method covers the determination of the force required to propagate a single-rip tear starting from a cut in a fabric and using a falling-pendulum (Elmendorf-Type) apparatus. 1.2 This test method applies to most fabrics including woven, layered blankets, napped pile, blanket, and air...

ASTM D8644-25 - Standard Practice for Recovered Carbon Black (rCB), Reduction, Blending, and Drying of Gross Samples for Testing
November 1, 2025 - ASTM International

4.1 Several test methods for recovered carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice...

ASTM E3189-19(2025) - Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Static Headspace Concentration onto an Adsorbent Tube
November 1, 2025 - ASTM International

1.1 This practice describes the procedure for separation of ignitable liquid residues from fire debris samples using static headspace concentration onto an adsorbent tube, for subsequent solvent elution or thermal desorption. 1.2 Static headspace concentration onto an adsorbent tube involves...

ASTM E1234-12(2025) - Standard Practice for Handling, Transporting, and Installing Nonvolatile Residue (NVR) Sample Plates Used in Environmentally Controlled Areas for Spacecraft
September 1, 2025 - ASTM International

This practice covers the proper procedures for handling, transporting, and installing sample plates used for the gravimetric determination of nonvolatile residue (NVR) within and between environmentally controlled facilities for spacecraft. This procedure shall appropriately require the following...

ASTM D6913/D6913M-17(2025) - Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
October 1, 2025 - ASTM International

1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...

ASTM D5126-25 - Standard Guide for Comparison of Field Methods for Determining Hydraulic Conductivity in Vadose Zone
August 15, 2025 - ASTM International

5.1 Saturated hydraulic conductivity measurements are made for a variety of purposes varying from design of landfills and construction of clay liners to assessment of irrigation systems. Infiltrometers are commonly used where infiltration or percolation rates through a surface or subsurface layer...

ASTM D8057-17(2025) - Standard Specification for Inlet Filters with a Rigid Frame
April 1, 2025 - ASTM International

1.1 This specification covers geosynthetic storm sewer inlet filters used in highway drainage, roadway, residential, commercial, and industrial applications. The inlet filter is comprised of a rigid frame and a removable geosynthetic sediment bag. The sediment bag hangs suspended from...

ASTM D5817-20(2025) - Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing
June 1, 2025 - ASTM International

4.1 Several test methods for carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice provides...

ASTM F3749-25 - Standard Practice for Assessment Method for Exoskeletons in Logistics
June 1, 2025 - ASTM International

1.1 This practice covers a method for testing exoskeletons on human subjects in realistic simulated working scenarios described as a test method for logistic tasks, such as in box and bag handling. 1.2 The effectiveness of exoskeletons depends on the use cases, therefore studies should be...

ASTM D6752/D6752M-25 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
May 1, 2025 - ASTM International

4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203/D3203M, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific...

ASTM F3006-25 - Standard Specification for Ball Drop Impact Resistance of Laminated Architectural Flat Glazing
May 1, 2025 - ASTM International

1.1 This specification covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications. 1.2 This specification is intended for use as an in-plant quality control test to evaluate the impact performance of laminated flat glass when a 2...

Advertisement