4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...
1.1 These test methods evaluate the flexural bond strength, normal to the bed joints, of masonry built of manufactured masonry units. Sampling and testing procedures are referenced, and terms are defined. Three different specimen fabrication methods are specified, each for a different purpose: 1.1...
4.1 In this test method, a compacted sample is vacuum sealed inside a plastic bag. The density of the sample, SG1, is calculated using a water displacement method, with the sample sealed. With the sample still in water, the bag is cut open. Since the sample is under vacuum and the air...
1.1 These test methods cover transverse load testing to determine the structural properties of wall segments. 1.2 These test methods serve to evaluate the performance of wall panels subject to transverse bending loads applied perpendicular to the plane of the wall. The tests are conducted on...
1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs). These...
1.1 This test method covers the measurement of the thickness of most textile materials. 1.2 This test method applies to most fabrics including woven fabrics, air bag fabrics, blankets, napped fabrics, knitted fabrics, layered fabrics, and pile fabrics. The fabrics may be untreated, heavily...
4.1 Several test methods for carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice provides...
4.1 In this test method, a compacted sample is vacuum sealed inside a plastic bag. The density of the sample, SG1, is calculated using a water displacement method, with the sample sealed. With the sample still in water, the bag is cut open. Since the sample is under vacuum and the air...
5.1 This test method is not considered satisfactory for acceptance testing of commercial shipments of fabrics because the between-laboratory precision of the test method is poor (see 15.1). 5.1.1 If there are differences of practical significance between reported test results for two laboratories...
1.1 This test method covers the determination of the force required to propagate a single-rip tear starting from a cut in a fabric and using a falling-pendulum (Elmendorf-Type) apparatus. 1.2 This test method applies to most fabrics including woven, layered blankets, napped pile, blanket, and air...
4.1 Several test methods for recovered carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice...
1.1 This practice describes the procedure for separation of ignitable liquid residues from fire debris samples using static headspace concentration onto an adsorbent tube, for subsequent solvent elution or thermal desorption. 1.2 Static headspace concentration onto an adsorbent tube involves...
This practice covers the proper procedures for handling, transporting, and installing sample plates used for the gravimetric determination of nonvolatile residue (NVR) within and between environmentally controlled facilities for spacecraft. This procedure shall appropriately require the following...
1.1 Soils consist of particles with various shapes and sizes. This test method is used to separate particles into size ranges and to determine quantitatively the mass of particles in each range. These data are combined to determine the particle-size distribution (gradation). This test method uses a...
5.1 Saturated hydraulic conductivity measurements are made for a variety of purposes varying from design of landfills and construction of clay liners to assessment of irrigation systems. Infiltrometers are commonly used where infiltration or percolation rates through a surface or subsurface layer...
1.1 This specification covers geosynthetic storm sewer inlet filters used in highway drainage, roadway, residential, commercial, and industrial applications. The inlet filter is comprised of a rigid frame and a removable geosynthetic sediment bag. The sediment bag hangs suspended from...
4.1 Several test methods for carbon black require the reduction in sample size or the blending of the test sample to reduce the variation of the measured characteristic. Other factors being equal, larger samples will tend to be more representative of the total supply. This practice provides...
1.1 This practice covers a method for testing exoskeletons on human subjects in realistic simulated working scenarios described as a test method for logistic tasks, such as in box and bag handling. 1.2 The effectiveness of exoskeletons depends on the use cases, therefore studies should be...
4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203/D3203M, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific...
1.1 This specification covers the destructive ball drop testing of laminated flat glass products intended for use in architectural glazing applications. 1.2 This specification is intended for use as an in-plant quality control test to evaluate the impact performance of laminated flat glass when a 2...
Narrow Your Results