1.1 This test method covers the determination of center spring constant, forebody spring constant, and afterbody spring constant of Alpine skis. In addition, it covers a method for determination of the spring constant balance. 1.2 This standard does not purport to address all of the safety...
This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with...
5.1 Thermal power curves are used to evaluate the isothermal hydration kinetics of the combined mixture of different materials during the early period after being mixed with water. These isothermal power curves, or hydration profiles, may provide indications relative to setting characteristics,...
This specification covers engineered wood fiber for use as a playground safety surface under and around playground equipment. This specification establishes minimum requirements for the factors that determine particle size, consistency, purity, ability to drain, and heavy metal concentrations...
4.1 For many structural ceramic components in service, their use is often limited by lifetimes that are controlled by a process of SCG. This test method provides the empirical parameters for appraising the relative SCG susceptibility of ceramic materials under specified environments. Furthermore,...
4.1 For many structural ceramic components in service, their use is often limited by lifetimes that are controlled by a process of slow crack growth. This test method provides the empirical parameters for appraising the relative slow crack growth susceptibility of ceramic materials under specified...
1.1 This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of airsoft...
1.1 This specification covers a group of cast duplex stainless steels (austenitic/ferritic
1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform...
5.1 Commercial trace detectors are used by first responders, security screeners, the military, and law enforcement to detect and identify explosive threats and drugs of interest quickly. These trace detectors typically operate by detecting chemical agents in residues and particles sampled from...
1.1 This test method covers a rapid and quantitative determination of the residue in emulsified asphalt binder using a moisture balance analyzer. It is applicable to all nonsolvent-containin
This test method covers the procedures for the standard practice of performing magnetic particle examination of continuous grain flow crankshaft forgings intended for medium speed diesel engines. Crankshafts shall be divided into four zones of decreasing operational stress, each of which have been...
This specification covers airworthiness requirements for the design of powered fixed wing light sport aircraft, an "airplane." In order to comply with flight requirements, the following shall be evaluated: load distribution limit, propeller speed and pitch limit, stalling speed, takeoff, climb,...
1.1 These test methods address compression (P) and shear (S) waves propagating in the downward direction in a nearly vertical plane. The seismic waves can be denoted as PV or PZ for a downward propagating compression wave and as SVH or SZX for downward propagating and horizontally polarized shear...
1.1 This guide presents a framework for a stakeholder-focused,
1.1 This test method provides data for determining undrained strength properties and stress-strain relations for cohesive soils. This test method provides for the measurement of the total stresses applied to the specimen, that is, the stresses are not corrected for pore-water pressure. 1.2 This...
5.1 Need for Heat Flux Measurements: 5.1.1 Independent measurements of temperature and heat flux support the development and validation of engineering models of fires and other high environments, such as furnaces. For tests of fire protection materials and structural assemblies, temperature and...
1.1 This practice defines the physical protection and control of moveable property in storage locations. 1.2 Generally, organizations should establish and maintain control of moveable property through means of storage in a manner that will strike a balance between cost of storage and the...
Narrow Your Results