1.1 This test method covers the evaluation of the performance of lubricating greases in ball bearings operating under light loads at high speeds and elevated temperatures. 1.2 The values stated in SI units are to be regarded as standard. 1.2.1 Exception-The values given in parentheses are...
This standard covers the specifications for physical properties and performance requirements of virgin impregnated activated carbon to be used for the removal of gaseous radioiodine species from gas streams. The activated carbon furnished under this specification shall be virgin material. Each...
5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to diesel...
5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to diesel...
1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI units are...
1.1 This guide covers and is intended for use in interpreting the friction forces recorded in reciprocating tribosystems. The guide applies to any reciprocating tribosystem, whether it is a wear or fretting test or an actual machine or device. 1.2 The energy dissipation guide was developed in...
1.1 This test method covers the determination of the load-carrying properties of lubricating greases. Three determinations are made: 1.1.1 Load-Wear Index (formerly called Mean-Hertz Load), 1.1.2 Weld Point, by means of the Four-Ball Extreme-Pressure (EP) Tester, and 1.1.3 Last nonseizure...
1.1 These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. 1.2 The scope of each of these test methods appears in the section in which the test method is described. 1.3 The test methods appear in the following sections: Test...
5.1 Wear due to excessive friction resulting in shortened life of engine components such as fuel pumps and fuel controls has sometimes been ascribed to lack of lubricity in an aviation fuel. 5.2 The relationship of test results to aviation fuel system component distress due to wear has been...
3.1 The Pusey and Jones indentation value is the depth of indentation, expressed in hundredths of a millimetre, of a ball 3.175 mm (0.1250 in.) in diameter under an expressed force of 9.8 N (2.2 lbf). This value may be used to compare the indentation resistance of rubber and rubber-like...
1.1 This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of airsoft...
1.1 This test method covers a procedure for measuring the hardness of vulcanized or thermoplastic rubber. The hardness is obtained by the difference in penetration depth of a specified dimension ball under two conditions of contact with the rubber: (1) with a small initial force and (2) with...
1.1 This test method covers the determination of the load-carrying properties of lubricating fluids. The following two determinations are made: 1.1.1 Load-wear index (formerly Mean-Hertz load). 1.1.2 Weld point by means of the four-ball extreme-pressure (EP) tester. 1.2 For the determination...
1.1 This test method covers a procedure for making a preliminary evaluation of the anti-wear properties of fluid lubricants in sliding contact by means of the Four-Ball Wear Test Machine. Evaluation of lubricating grease using the same machine is detailed in Test Method D2266. 1.2 The values...
1.1 This test method covers a procedure for determining the coefficient of friction by means of the Four-Ball Wear Test Machine.2 1.2 The values stated in either SI units or in the former cm-kgf metric units are to be regarded separately as the standard. Within the text the cm-kgf units are...
3.1 Adjustment methods provide a means for combining the results of neutron transport calculations with neutron dosimetry measurements (see Test Method E1005 and NUREG/CR-5049) in order to obtain optimal estimates for neutron damage exposure parameters with assigned uncertainties. The inclusion of...
5.1 The significance of the number of scratches as far as correlation with field performance is concerned has not been established. A particle which is abrasive to plastic will not necessarily be abrasive to steel or other bearing materials. Some correlation was obtained in that the contaminant...
1.1 This test method covers the determination of the softening point of asphalt and pitch in the range from 50?°C to 180?°C by the cup-and-ball apparatus, and gives results comparable to those obtained by Test Method D36. Note 1: If the softening point of asphalt by this Mettler...
1.1 This test method covers a procedure for determining a lubricating grease's coefficient of friction and its ability to protect against wear when subjected to high-frequency, linear-oscillation motion using an SRV test machine at a test load of 200?N, frequency of 50?Hz, stroke amplitude of 1...
Narrow Your Results