loading
ASTM D3336-26 - Standard Test Method for Life of Lubricating Greases in Ball Bearings at Elevated Temperatures
May 1, 2026 - ASTM International

1.1 This test method covers the evaluation of the performance of lubricating greases in ball bearings operating under light loads at high speeds and elevated temperatures. 1.2 The values stated in SI units are to be regarded as standard. 1.2.1 Exception-The values given in parentheses are...

ASTM D4069-95(2026)e1 - Standard Specification for Impregnated Activated Carbon Used to Remove Gaseous Radio-Iodines from Gas Streams
June 1, 2026 - ASTM International

This standard covers the specifications for physical properties and performance requirements of virgin impregnated activated carbon to be used for the removal of gaseous radioiodine species from gas streams. The activated carbon furnished under this specification shall be virgin material. Each...

ASTM D6079-26 - Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR)
June 1, 2026 - ASTM International

5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to diesel...

ASTM D7688-26 - Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) by Visual Observation
June 1, 2026 - ASTM International

5.1 Diesel fuel injection equipment has some reliance on lubricating properties of the diesel fuel. Shortened life of engine components, such as diesel fuel injection pumps and injectors, has sometimes been ascribed to lack of lubricity in a diesel fuel. 5.2 The trend of HFRR test results to diesel...

ASTM D6557-26 - Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils
June 1, 2026 - ASTM International

1.1 This test method covers a Ball Rust Test (BRT) procedure for evaluating the anti-rust ability of fluid lubricants. The procedure is particularly suitable for the evaluation of automotive engine oils under low-temperature, acidic service conditions. 1.2 The values stated in SI units are...

ASTM G203-10(2026) - Standard Guide for Determining Friction Energy Dissipation in Reciprocating Tribosystems
June 1, 2026 - ASTM International

1.1 This guide covers and is intended for use in interpreting the friction forces recorded in reciprocating tribosystems. The guide applies to any reciprocating tribosystem, whether it is a wear or fretting test or an actual machine or device. 1.2 The energy dissipation guide was developed in...

ASTM D2596-26 - Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Grease (Four-Ball Method)
March 1, 2026 - ASTM International

1.1 This test method covers the determination of the load-carrying properties of lubricating greases. Three determinations are made: 1.1.1 Load-Wear Index (formerly called Mean-Hertz Load), 1.1.2 Weld Point, by means of the Four-Ball Extreme-Pressure (EP) Tester, and 1.1.3 Last nonseizure...

ASTM D751-26 - Standard Test Methods for Coated Fabrics
June 1, 2026 - ASTM International

1.1 These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. 1.2 The scope of each of these test methods appears in the section in which the test method is described. 1.3 The test methods appear in the following sections: Test...

ASTM D5001-26 - Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)
March 1, 2026 - ASTM International

5.1 Wear due to excessive friction resulting in shortened life of engine components such as fuel pumps and fuel controls has sometimes been ascribed to lack of lubricity in an aviation fuel. 5.2 The relationship of test results to aviation fuel system component distress due to wear has been...

ASTM D531-15(2026) - Standard Test Method for Rubber Property—Pusey and Jones Indentation
April 1, 2026 - ASTM International

3.1 The Pusey and Jones indentation value is the depth of indentation, expressed in hundredths of a millimetre, of a ball 3.175 mm (0.1250 in.) in diameter under an expressed force of 9.8 N (2.2 lbf). This value may be used to compare the indentation resistance of rubber and rubber-like...

ASTM F2879-22(2026) - Standard Specification for Eye Protective Devices for Airsoft Sports
May 1, 2026 - ASTM International

1.1 This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of airsoft...

ASTM D1415-18(2026) - Standard Test Method for Rubber Property—International Hardness
April 1, 2026 - ASTM International

1.1 This test method covers a procedure for measuring the hardness of vulcanized or thermoplastic rubber. The hardness is obtained by the difference in penetration depth of a specified dimension ball under two conditions of contact with the rubber: (1) with a small initial force and (2) with...

ASTM D2783-25 - Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids (Four-Ball Method)
December 1, 2025 - ASTM International

1.1 This test method covers the determination of the load-carrying properties of lubricating fluids. The following two determinations are made: 1.1.1 Load-wear index (formerly Mean-Hertz load). 1.1.2 Weld point by means of the four-ball extreme-pressure (EP) tester. 1.2 For the determination...

ASTM D4172-25 - Standard Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method)
December 1, 2025 - ASTM International

1.1 This test method covers a procedure for making a preliminary evaluation of the anti-wear properties of fluid lubricants in sliding contact by means of the Four-Ball Wear Test Machine. Evaluation of lubricating grease using the same machine is detailed in Test Method D2266. 1.2 The values...

ASTM D5183-25 - Standard Test Method for Determination of the Coefficient of Friction of Lubricants Using the Four-Ball Wear Test Machine
December 1, 2025 - ASTM International

1.1 This test method covers a procedure for determining the coefficient of friction by means of the Four-Ball Wear Test Machine.2 1.2 The values stated in either SI units or in the former cm-kgf metric units are to be regarded separately as the standard. Within the text the cm-kgf units are...

ASTM E944-26 - Standard Guide for Application of Neutron Spectrum Adjustment Methods in Reactor Surveillance
February 1, 2026 - ASTM International

3.1 Adjustment methods provide a means for combining the results of neutron transport calculations with neutron dosimetry measurements (see Test Method E1005 and NUREG/CR-5049) in order to obtain optimal estimates for neutron damage exposure parameters with assigned uncertainties. The inclusion of...

ASTM D1404/D1404M-99(2025) - Standard Test Method for Estimation of Deleterious Particles in Lubricating Grease
November 1, 2025 - ASTM International

5.1 The significance of the number of scratches as far as correlation with field performance is concerned has not been established. A particle which is abrasive to plastic will not necessarily be abrasive to steel or other bearing materials. Some correlation was obtained in that the contaminant...

ASTM D3461-25 - Standard Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-and-Ball Method)
July 1, 2025 - ASTM International

1.1 This test method covers the determination of the softening point of asphalt and pitch in the range from 50?°C to 180?°C by the cup-and-ball apparatus, and gives results comparable to those obtained by Test Method D36. Note 1: If the softening point of asphalt by this Mettler...

ASTM D5707-25 - Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
November 1, 2025 - ASTM International

1.1 This test method covers a procedure for determining a lubricating grease's coefficient of friction and its ability to protect against wear when subjected to high-frequency, linear-oscillation motion using an SRV test machine at a test load of 200?N, frequency of 50?Hz, stroke amplitude of 1...

Advertisement