FOREWORD: Each year in the United States several thousand wells are drilled and completed - some productive of oil or gas and some dry - and during this drilling and completion most of these wells are cased, with the casing set in the bore hole surrounded by oil-well cement. This book...
1.1 These practices describe laboratory procedures for preparing an oil-based ink resin solution in a high-boiling solvent using four pieces of lab equipment: (1) A hot oil bath (Sections 4 to 11), (2) A stirrer/hot plate (Sections 12 to 16), (3) An industrial blender (Sections...
This specification covers sintered bronze, oil-impregnated bearings made primarily from elemental copper, tin, lead, and graphite powders. This specification covers the following variables: Grades (available in three bronze base compositions identifiable by different graphite contents...
This specification covers the standard requirements for porous metallic sleeve, flange, thrust, and spherical iron-base bearings that are produced from mixed metal powder metallurgy technology and then impregnated with oil to supply operating lubrication. Porous iron-base...
5.1 New and used petroleum products can contain basic constituents that are present as additives. The relative amount of these materials can be determined by titration with acids. The base number is a measure of the amount of basic substances in the oil always under the conditions of...
5.1 The loss of volatile materials from greases and oils can adversely affect the original performance characteristics of a lubricant and, therefore, could be a significant factor in evaluating a lubricant for a specific use. Such volatiles can also be considered contaminants in the environment in...
1.1 This specification covers a high fire point natural vegetable oil ester insulating fluid for use as a dielectric and cooling medium in new and existing power and distribution electrical apparatus such as transformers and attendant equipment. 1.2 Natural vegetable oil ester...
1.1 This test method covers the determination of additive elements, wear metals, and contaminants in used and unused lubricating oils and base oils by inductively coupled plasma atomic emission spectrometry (ICP-AES). The specific elements are listed in Table 1. 1.2 This test method covers...
5.1 Permanent Shear Stability Index (PSSI) is a measure of the loss of viscosity, due to shearing, contributed by a specified additive. Note 2: For example, a PSSI of 50 means the additive will lose 50?% of the viscosity it contributes to the finished oil. 5.2 The selection of appropriate...
5.1 New and used petroleum products can contain basic constituents that are present as additives. The relative amounts of these materials can be determined by titration with acids. The base number is a measure of the amount of basic substance in the oil, always under the conditions of...
1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids; such as base oils, formulated oils, diesel oil, biodiesel, biodiesel blends, residual fuel oils, marine fuels, and used lubricating oils using a Houillon viscometer in automated...
1.1 This test method covers the determination of total sulfur in petroleum and petroleum products that are single-phase and either liquid at ambient conditions, liquefiable with moderate heat, or soluble in hydrocarbon solvents. These materials can include diesel fuel, jet fuel, kerosene, other...
This specification covers mineral lubricating oils used in steam and gas turbine lubricating systems where the performance requirements demand a highly refined mineral base oil compounded with rust and oxidation inhibitors plus selected additives as needed to control foam, wear,...
5.1 This test method was originally developed to evaluate oxidation stability of re-refined lubricating base oils combined with additives chemistries similar to those found in gasoline engine oils and service.2 5.2 This test method is useful for screening formulated oils before engine tests....
1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids; such as base oils, formulated oils, diesel oil, biodiesel, biodiesel blends, residual fuel oils, marine fuels, and used lubricating oils using a Houillon viscometer in automated...
5.1 Visual interpretation of gear teeth condition, such as contact patterns, scuffing, and wear, differs from examination for surface-breaking cracks or early signs of macro-pitting. Guidance for visual interpretation of gear tooth condition is provided in ASNI/AGMA 1010-F14. 5.2 Eddy current array...
5.1 Lubricants can contain basic constituents that are present as additives. The relative amount of these materials can be determined by titration with acids. The base number is a measurement of the amount of basic substances in the oil under the conditions of the testing procedure. 5...
5.1 Agitation of lubricating oil with air in equipment, such as bearings, couplings, gears, pumps, and oil return lines, may produce a dispersion of finely divided air bubbles in the oil. If the residence time in the reservoir is too short to allow the air bubbles to rise to...
5.1 In the absence of water, the crude oil is noncorrosive. However, trace amounts of water and sediment have the potential to create corrosive situations during crude oil handling or transport if such materials accumulate and persist on steel surfaces. Test Methods D473 and D4006...
The material defined by this specification is a NLGI Grade 2 synthetic lubricating grease consisting of a perfluoropolyether (PFPE) base oil and thickened with polytetrafluoroethyl
Narrow Your Results