1.1 This consumer safety specification covers the establishment of performance requirements and corresponding test methods used to minimize the hazards to users of electric-powered scooters for rent or lease by multiple users but not individually owned units. For example, electric-powered scooters...
1.1 This specification covers requirements for the design, installation and qualification of rechargeable lithium batteries based electrical energy storage systems (EESS) on light sport category aircraft used for propulsion purposes. The manufacturer shall comply with all applicable...
1.1 This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments: 1.1.1 Power Supply Section: ??????line regulation, ???????battery discharge time, and ???????battery charge time. 1.1.2 Pulser...
5.1 The ER of a battery separator is a standard measurement used by separator and battery manufacturers for quality control purposes and separator selection. 5.2 Separator ER and the separator's interaction with the electrolyte, that is resistance to wetting or flow, will contribute...
1.1 This practice establishes minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. This practice is intended for aerospace applications using the wet fluorescent method. Refer to Practice E3024/E3024M...
1.1 This practice covers minimum requirements for the design and manufacture of Electric Propulsion Units (EPU) for light sport aircraft, VFR use. The EPU shall as a minimum consist of the electric engine, associated controllers, disconnects and wiring, an Energy Storage Device (ESD) such as a...
5.1 Electrical conductivity is a critical physical property for thermal management fluids with intended use in electrical applications such as battery electric and fuel cell vehicles. A fluid's electrical conductivity is used to assess its compatibility and safety with these systems, and...
5.1 These basic requirements for response robots that help enhance the safety and effectiveness of responders or soldiers include: the robots are designed to be remotely operated from safe standoff distances, deployable at operational tempos, capable of operating in complex environments,...
1.1 This consumer safety specification establishes safety performance requirements, test methods, and labeling requirements to minimize the hazards to infants presented by swings as identified in the introduction. 1.2 This consumer safety specification is intended to minimize the risk of injuries...
4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...
1.1 The purpose of this guide is to provide standard methods for the safe use of lithium ion (Li-ion) batteries onboard vessels. The guidelines in this document were developed primarily for larger Li-ion marine battery installations, such as for propulsion or ships service electrical...
1.1 This test method covers the usage of a chamber system equipped with a CO2 reference monitor to evaluate the performance of stationary indoor air quality CO2 sensors and CO2 sensor systems used for CO2 detection and measurement. 1.2 This test method evaluates, under steady state conditions (CO2...
1.1 This specification covers airsoft guns which propel a projectile by means of energy released by compressed gas, compressed CO2, mechanical springs, battery or a combination thereof, used in the sport commonly called airsoft or air soft, and is to be used in conjunction with Specification...
1.1 This practice establishes minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. This practice is intended for aerospace applications using the wet fluorescent method. Refer to Practice E3024/E3024M...
1.1 These requirements cover battery chargers rated 600 volts or less. They are intended to be used in accordance with the National Electrical Code, NFPA 70, to charge industrial storage batteries which are used to provide power for material handling trucks, tractors, personnel...
1.1 Definition-This specification defines acceptable means and methods to validate the equipment, location, and installation of rechargeable lithium batteries and battery systems on aircraft, given special considerations for the particular characteristics inherent with the use of...
This specification applies to the electrical systems aspects of airworthiness and design for "small" aircraft. It establishes the Aircraft Type Code (ATC) compliance matrix based on airworthiness level, number of engines, type of engine(s), stall speed, cruise speed, meteorological conditions,...
1.1 This consumer safety specification establishes performance requirements, test methods and marking requirements to promote safe use of recreational powered scooters and pocket bikes intended for use by children age eight to twelve years, and adolescents age thirteen and above. This consumer...
1.1 This guide is intended to assist the testing laboratory in the conduct and evaluation of tumorigenicity tests to evaluate the potential for materials to evoke a neoplastic response. 1.2 Carcinogenicity, which includes tumorigenic potential, is one of several biological effects that should be...
Narrow Your Results