loading
PLAN ANALYST BEAM & COLUM - PLAN ANALYST BEAM & COLUMN CALCULATOR SOFTWARE
January 1, 2000 - BEN WEESE
A description is not available for this item.
ASTM 51818-26 - Standard Practice for Dosimetry in an Electron Beam Facility for Radiation Processing at Energies Between 80 and 300 keV
June 1, 2026 - ASTM International

1.1 This practice covers dosimetric procedures to be followed in installation qualification, operational qualification, performance qualification (IQ, OQ, PQ), and routine processing at electron beam facilities to ensure that the product has been treated with an acceptable range of absorbed...

ASTM E1570-19(2026) - Standard Practice for Fan Beam Computed Tomographic (CT) Examination
May 1, 2026 - ASTM International

5.1 This practice establishes the basic parameters for the application and control of fan-beam CT examinations. This practice is written so it can be specified on the engineering drawing, specification, or contract. It will require a detailed procedure delineating the technique or procedure...

ASTM G168-26 - Standard Practice for Making and Using Precracked Double Beam Stress Corrosion Specimens
May 1, 2026 - ASTM International

1.1 This practice covers procedures for fabricating, preparing, and using precracked double beam stress corrosion test specimens. This specimen configuration was formerly designated the double cantilever beam (DCB) specimen. Guidelines are given for methods of exposure and inspection....

ASTM B365-12(2026) - Standard Specification for Tantalum and Tantalum Alloy Rod and Wire
July 1, 2026 - ASTM International

This specification covers unalloyed and alloyed tantalum rod and wire. The materials covered are: R05200, R05400, R05255, R05252, and R05240. These materials shall be made from vacuum-arc melted or electron-beam melted ingots or powder-metallurgy consolidated unalloyed tantalum. The chemical...

ASTM E1001-21(2026) - Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves
July 1, 2026 - ASTM International

6.1 This practice provides guidelines for the application of immersed longitudinal wave examination to the detection and quantitative evaluation of discontinuities in materials. 6.2 Although not all requirements of this practice can be applied universally to all examination situations and...

ASTM B737-10(2026) - Standard Specification for Hot-Rolled and/or Cold-Finished Hafnium Rod and Wire
July 1, 2026 - ASTM International

This specification covers hot-, cold-, or both hot- and cold-rolled hafnium rods and wires in either one of two grades. All grades should be in the recrystallization annealed condition unless specified otherwise. The materials should be made from ingots produced by vacuum melting in an electron...

ASTM C1368-18(2026) - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Rate Strength Testing at Ambient Temperature
June 1, 2026 - ASTM International

1.1 This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress rate rectangular beam flexural testing, ring-on-ring biaxial disk flexural testing, or direct tensile strength, in which strength is determined as a function of...

ASTM C1623-26 - Standard Specification for Solid Dry-Cast Manufactured Concrete Masonry Lintels
June 1, 2026 - ASTM International

1.1 This specification covers dry-cast concrete masonry lintels (beams) that are solid in cross-section, are reinforced for flexure, and are machine-made from hydraulic cement, water, and suitable mineral aggregates with or without the inclusion of other materials. These lintels are suitable...

ASTM E1935-26 - Standard Practice for Calibrating and Measuring CT Density
June 15, 2026 - ASTM International

6.1 This practice allows specification of the density calibration procedures to be used to calibrate and perform material density measurements using CT image data. Such measurements can be used to evaluate parts, characterize a particular system, or compare different systems, provided that observed...

ASTM ASTM51631-26 - Standard Practice for Use of Calorimetric Dosimetry Systems for Dose Measurements and Routine Dosimetry System Calibration in Electron Beams
May 1, 2026 - ASTM International

4.1 This practice is applicable to the use of calorimetric dosimetry systems for the measurement of absorbed dose in electron beams, the qualification of electron irradiation facilities, periodic checks of the performance of electron irradiation facilities, and calibration of other dosimetry...

ASTM D7244-20(2026) - Standard Test Method for Relative Cure of Energy-Cured Inks and Coatings
June 1, 2026 - ASTM International

1.1 This test method covers the procedure for evaluating the relative cure of printed energy-cured (ultraviolet or electron beam) ink or coating by a mechanical solvent rub test using a motorized Crockmeter. 1.2 This test method is applicable to laboratory and production prints on any flat...

ASTM E803-20(2026) - Standard Test Method for Determining the L/D? Ratio of Neutron Radiography Beams
May 1, 2026 - ASTM International

1.1 This test method defines an empirical technique for the measurement of the effective collimation ratio, L/D, of neutron radiography beams. The technique is based upon analysis of a neutron radiographic image and is independent of measurements and calculations based on physical dimensions...

ASTM D8160-20(2026) - Standard Test Method for Un-notched Cantilever Beam Impact Resistance (Izod Impact) Testing of Thermoplastic Pavement Marking Materials
March 1, 2026 - ASTM International

1.1 This test method covers the sample preparation for cantilever beams and test methodology of thermoplastic pavement marking materials, similar to the "Izod Impact" method listed in Test Method D4812. 1.1.1 Some methods call for results in inch pound-force (in.·lbf) as opposed to the...

ASTM C1465-26 - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
June 1, 2026 - ASTM International

4.1 For many structural ceramic components in service, their use is often limited by lifetimes that are controlled by a process of slow crack growth. This test method provides the empirical parameters for appraising the relative slow crack growth susceptibility of ceramic materials under specified...

ASTM E2032-26 - Standard Practice for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E?119
June 1, 2026 - ASTM International

1.1 This practice covers the extension of fire resistance ratings obtained from fire tests performed in accordance with Test Method E119 to constructions that have not been tested. Test Method E119 evaluates the duration for which test specimens will contain a fire, retain their standard integrity,...

ASTM D5379/D5379M-19(2026) - Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
April 15, 2026 - ASTM International

5.1 This test method is designed to produce shear property data for material specifications, research and development, quality assurance, and structural design and analysis. Either in-plane or interlaminar shear properties may be evaluated, depending upon the orientation of the material coordinate...

ASTM F606/F606M-26a - Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
May 15, 2026 - ASTM International

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for...

ASTM E1419/E1419M-26 - Standard Practice for Examination of Seamless, Gas-Filled, Pressure Vessels Using Acoustic Emission
May 1, 2026 - ASTM International

1.1 This practice provides guidelines for acoustic emission (AE) examinations of seamless pressure vessels (tubes) of the type used for distribution or storage of industrial gases. 1.2 This practice requires pressurization to a level greater than normal use. Pressurization medium may be gas or...

ASTM A388/A388M-26 - Standard Practice for Ultrasonic Examination of Steel Forgings
April 1, 2026 - ASTM International

1.1 This practice covers the examination procedures for the contact, pulse-echo ultrasonic examination of steel forgings by the straight- and angle-beam techniques. The straight-beam techniques include utilization of the DGS (distance gain-size) method. See Appendix X3. 1.2 This...

Advertisement