loading
ASTM D6557-26 - Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils
June 1, 2026 - ASTM International

5.1 This bench test method was designed as a replacement for Test Method D5844. Test Method D5844 was designed to measure the ability of an engine oil to protect valve train components against rusting or corrosion under low temperature, short-trip service, and was correlated with vehicles in...

ASTM F3067-26 - Standard Guide for Radial Loading of Balloon-Expandable and Self-Expanding Vascular Stents
May 1, 2026 - ASTM International

1.1 This document provides guidance for developing in vitro test methods for measuring the radial strength or collapse pressure of balloon-expandable vascular stents and chronic outward force of self-expanding vascular stents. 1.2 This guide is applicable to balloon-expandable and self-expanding...

ASTM F1971-12(2026)e1 - Standard Test Method for Electrical Resistance of Tires Under Load On the Test Bench
February 1, 2026 - ASTM International

5.1 Occasions exist where static charges on the vehicle must be dissipated by way of the tires. Electrical resistance inversely measures the tire's ability to dissipate static charge from the vehicle.

ASTM F1550-26 - Standard Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter
January 1, 2026 - ASTM International

1.1 This fire-test-response test method is designed for use to determine various fire-test-response characteristics, including ignitability and heat release rate, from composites of mattresses or furniture, or correctional facilities, which have been vandalized in a prescribed manner to expose the...

ASTM E3300-26 - Standard Guide for Non-Aqueous Phase Liquid (NAPL) Mobility and Migration in Sediment—Factors Affecting Ebullition and Evaluating Ebullition Activity and the Associated Ebullition-Facilitated Transport of NAPL/Contaminants
April 1, 2026 - ASTM International

4.1 Intended Users: 4.1.1 This guide may be used by various parties involved in programs evaluating ebullition activity or NAPL/contaminants EFT in sediment (or both), including regulatory agencies, project sponsors, environmental consultants, risk assessors, site remediation professionals,...

ASTM E824-26 - Standard Test Method for Transfer of Calibration From Reference to Field Radiometers
March 1, 2026 - ASTM International

5.1 The methods described represent the preferable means for calibration of field radiometers employing standard reference radiometers. Other methods involve the employment of an optical bench and essentially a point source of artificial light. While these methods are useful for cosine and...

ASTM D5183-25 - Standard Test Method for Determination of the Coefficient of Friction of Lubricants Using the Four-Ball Wear Test Machine
December 1, 2025 - ASTM International

5.1 This test method can be used to determine the coefficient of friction of lubricating fluids under the prescribed test conditions. The user of this test method should determine to his own satisfaction whether results of this test method correlate with field performance or other bench test...

ASTM D2783-25 - Standard Test Method for Measurement of Extreme-Pressure Properties of Lubricating Fluids (Four-Ball Method)
December 1, 2025 - ASTM International

5.1 This test method, used for specification purposes, differentiates between lubricating fluids having low, medium, and high level of extreme-pressure properties. The user of this method should determine to his own satisfaction whether results of this test procedure correlate with field...

ASTM E3093-26 - Standard Guide for Structured Small Group Product Evaluations
February 1, 2026 - ASTM International

1.1 This guide covers those occasions in which a small group of individuals (generally between three and ten) with potentially different functional roles and degrees of training in sensory and product evaluation reviews a product or series of products for a specific objective, with a pre-identified...

ASTM D2670-25 - Standard Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method)
December 1, 2025 - ASTM International

5.1 This test method may be used to determine wear obtained with fluid lubricants under the prescribed test conditions. The user of this test method should determine to his or her own satisfaction whether results of this test procedure correlate with field performance or other bench test...

ASTM D4172-25 - Standard Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method)
December 1, 2025 - ASTM International

5.1 This test method can be used to determine the relative wear preventive properties of lubricating fluids in sliding contact under the prescribed test conditions. No attempt has been made to correlate this test with balls in rolling contact. The user of this test method should determine to his...

ASTM E810-20(2025) - Standard Test Method for Coefficient of Retroreflection of Retroreflective Sheeting Utilizing the Coplanar Geometry
November 1, 2025 - ASTM International

1.1 This test method describes an instrument measurement of the retroreflective performance of retroreflective sheeting. 1.2 The user of this test method must specify the entrance and observation angles to be used, and may specify the rotation angles. 1.3 This test method is intended as a...

ASTM E1822-21(2025) - Standard Test Method for Fire Testing of Stacked Chairs
December 1, 2025 - ASTM International

5.1 This test method provides a means of measuring a variety of fire-test-response characteristics resulting from burning a stack of five stacking chairs. After ignition using a propane gas burner, the test specimen is permitted to burn freely under well-ventilated conditions. The most important...

ASTM F3211-17(2025) - Standard Guide for Fatigue-to-Fracture (FtF) Methodology for Cardiovascular Medical Devices
October 15, 2025 - ASTM International

5.1 Use of This Methodology: 5.1.1 This guide provides a compendium of information on methods to use fracture data, fatigue life models, and statistical techniques to estimate the structural fatigue durability of an implantable medical device under anticipated in vivo loading modes. The methodology...

ASTM D7208-25 - Standard Test Method for Determination of Temporary Ditch Check Performance in Protecting Earthen Channels from Stormwater-Induced Erosion
October 15, 2025 - ASTM International

1.1 This test method covers the guidelines, requirements, and procedures for evaluating the ability of temporary ditch check systems to protect earthen channels from stormwater-induced erosion. Critical elements of this protection are the ability of the temporary ditch check to: 1.1.1 Slow or pond...

ASTM F2942-25 - Standard Guide for in vitro Axial, Bending, Torsional, and Compression Durability Testing of Vascular Stents and Vascular Stent-Grafts
October 1, 2025 - ASTM International

1.1 This guide includes four separate cyclic deformation durability guides related to vascular stents and vascular stent-grafts: bending, axial, torsional, and compression. 1.2 This guide does not address whether a specific mode of durability testing is relevant for a particular vascular stent and...

ASTM D8151-25 - Standard Practice for Obtaining Rainfall Runoff from Unvegetated Rolled and Hydraulic Erosion Control Products (RECPs and HECPs) for Acute Ecotoxicity Testing
August 1, 2025 - ASTM International

1.1 This practice establishes the guidelines, requirements, and procedures for obtaining rainfall runoff of unvegetated rolled and hydraulic erosion control products (RECPs and HECPs) during bench-scale conditions from simulated rainfall to be sent out for acute ecotoxicity testing. 1.2 This...

ASTM D7038-25 - Standard Test Method for Evaluation of Moisture Corrosion Resistance of Automotive Gear Lubricants
July 1, 2025 - ASTM International

1.1 This test method covers a test procedure for evaluating the rust and corrosion inhibiting properties of a gear lubricant while subjected to water contamination and elevated temperature in a bench-mounted hypoid differential housing assembly.2 This test method is commonly referred to as...

ASTM F1592-12(2025) - Standard Test Methods for Detention Hollow Metal Vision Systems
June 1, 2025 - ASTM International

4.1 A major concern for corrections administration officials is the resistance of security barriers used in detention/correctional facilities to certain types of physical attack that it is reasonable to expect in the field. These test methods are designed to aid in identifying a level of physical...

ASTM F2322-12(2025) - Standard Test Methods for Physical Assault on Vertical Fixed Barriers for Detention and Correctional Facilities
June 1, 2025 - ASTM International

4.1 A major concern for administrative officials is the security of barriers used in detention/correctional facilities. These test methods are designed to aid in identifying levels of physical security for walls which enclose or separate secure areas. This does not apply to the passage of...

Advertisement