5.1 General Utility: 5.1.1 This practice is suitable for research, quality control, specification testing and process control. 5.1.2 It is useful to define and verify the reactivity of non-foam polyurethane formulations. 5.2 Limitations: 5.2.1 Operator-to-operator
1.1 This specification covers minimum requirements for the design and testing of rotors for light sport category gyroplanes. The rotor system is considered to include rotor blades, hub bar, connection structure of hub bar to the rotor blades as well as teeter block. 1.2 Units-The...
1.1 This practice covers guidelines for the evaluations of flushing vehicles for pigment dispersion using a vacuum modified sigma blade mixer, or vacuum flusher. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1...
4.1 Laboratory measurement of application properties of architectural coatings generally employ a blade-type applicators that lay down films of highly uniform thickness. Applicators, such as brushes and rollers, typically apply films that lack uniformity due to variations in rheology, film...
1.1 This speci?cation covers minimum requirements for Gyroplane, within the scope of Specification F3851?-?26 Specification for Light Sport Category Aircraft. Note 1: Referenced standards may have further limitations. 1.2 These requirements apply to gyroplanes having the following basic features: 1...
1.1 This practice provides tables of dimensions of preformed pipe insulation that shall be used in fabricating insulation covers for use on valves, ells, tees, flanges, and vessels in the pressure range from 150 to 1500 psi (1 to 10 MPa). These tables, which are part of this standard, are published...
3.1 Many test methods including Test Methods D882, D2838, F88/F88M, F1921/F1921M, and F2029 require the use of narrow strips of varying length. The quality of the sample preparation directly affects test results. This practice describes three techniques for preparing samples with straight, clean,...
1.1 This terminology defines basic terms and considerations for the components of scissors with either inserted or non-inserted blades (see Fig. 1). Instruments in this terminology are limited to those fabricated having scissor blades made from stainless steel and used for surgical...
2.1 Molybdenum is used in engineering applications where strength and rigidity of component parts are needed, especially at high temperatures. Its good strength at high temperatures, low vapor pressure, and good impact and creep resistance make it attractive for load-bearing items such as turbine...
1.1 This specification specifies the recommended physical characteristics of the steel blades required for the surface cut test described in ANSI/UL 1703 (Section 24) and IEC 61730-2 (Paragraph 10.3). 1.2 ANSI/UL 1703 and IEC 61730-2 are standards for photovoltaic module safety testing. 1.3...
5.1 This test method assesses the cut resistance of a material when exposed to a cutting edge under specified loads. Data obtained from this test method can be used to compare the cut resistance of different materials. 5.2 This test method only addresses that range of cutting hazards that are...
5.1 PCRT Applications and Capabilities-PCRT has been applied successfully to a wide range of NDT applications in the manufacture and maintenance of metallic and non-metallic parts. Examples of anomalies detected are discussed in 1.1. PCRT has been shown to provide cost effective and accurate NDT...
This specification covers fabrication techniques for cellular glass block into billets to fabricate pipe and tubing insulation. The optimization of the thermal performance of installed cellular glass insulation systems is discussed. This is best achieved by limiting the number of joints, in...
1.1 This specification covers stainless steel forgings for compressor and turbine bucket, blade, and airfoil applications. 1.2 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M designation (SI...
1.1 This test method covers the determination of the stiffness of fabrics by measuring the force required to push a specimen into a slot of predetermined width with a metal blade working at a predetermined capacity. Note 1: For other methods for testing stiffness, refer to Test Methods...
5.1 PCRT Applications and Capabilities-PCRT PTI examination has been applied successfully to a wide range of parts in manufacturing and maintenance environments. Examples of manufacturing processes, repair processes, and in-service damage mechanisms evaluated with PTI are discussed in 1.1. PCRT has...
5.1 Laboratory hiding power measurements of architectural coatings generally employ blade-type applicators that lay down films of highly uniform thickness. But practical applicators, such as rollers, pads, and brushes, typically apply films that lack uniformity due to incomplete leveling,...
4.1 Creep tests measure the time-dependent deformation under force at a given temperature, and, by implication, the force-carrying capability of the material for limited deformations. Creep rupture tests, properly interpreted, provide a measure of the force-carrying capability of the material as a...
1.1 This terminology defines basic terms and considerations for the components of scissors with either inserted or non-inserted blades (see Fig. 1). Instruments in this terminology are limited to those fabricated having scissor blades made from stainless steel and used for surgical...
1.1 These test methods cover three electrical tests on plastic guards and assembled guard systems. They are: 1.1.1 Method A-Withstand voltage proof test, 1.1.2 Method B-Flashover voltage, and 1.1.3 Method C-Leakage current. 1.1.4 This specification covers plastic guard equipment and guard systems...
Narrow Your Results