loading
ASTM D8271-26 - Standard Test Method for Direct Measurement of Surface Profile of Prepared Concrete
June 1, 2026 - ASTM International

4.1 Proper bonding of coatings and linings to concrete surfaces requires proper cleaning and frequently requires the concrete to be roughened to increase the surface area. The roughness, also known as surface profile, can be imparted into concrete by abrasive blast cleaning, acid etching or...

ASTM D2200-26 - Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces
June 1, 2026 - ASTM International

4.1 The appearance of the various degrees of dry and wet abrasive blast cleaning, hand and power tool cleaning, and water jetting are influenced by the initial rust grades of the steel being cleaned and/or the type and condition of the coating on the existing steel. The standards and guides...

ASTM D5367-26 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Additives Used to Prevent Flash Rusting of Steel When Vapor, Water, or Water/Abrasive Blasted
June 1, 2026 - ASTM International

1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC),...

ASTM E279-26 - Standard Test Method for Determination of Abrasion Resistance of Iron Ore Pellets, Lump, and Sinter by the Tumbler Test
May 1, 2026 - ASTM International

5.1 This test method is a comparative method intended primarily to test materials for compliance with compositional specifications or for monitoring. It is assumed that all who use these procedures will be trained analysts capable of performing common laboratory procedures skillfully and safely. It...

ASTM C404-26 - Standard Specification for Aggregates for Masonry Grout
June 1, 2026 - ASTM International

This specification covers aggregates used for masonry grout. Aggregates should consist of either natural or manufactured sand, used alone or in combination with course aggregates. The course aggregates should be made up of crushed stone, gravel, or processed air-cooled iron blast-furnace...

ASTM C144-26 - Standard Specification for Aggregate for Masonry Mortar
June 1, 2026 - ASTM International

This specification covers aggregate for use in masonry mortar. Aggregate for use in masonry mortar shall consist of natural sand or manufactured sand. Manufactured sand is the product obtained by crushing stone, gravel, or air-cooled iron blast-furnace slag specially processed to ensure...

ASTM B614-26 - Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
April 1, 2026 - ASTM International

This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. Grease,...

ASTM F86-21(2026) - Standard Practice for Surface Preparation and Marking of Metallic Surgical Implants
March 15, 2026 - ASTM International

3.1 The objective of surface treatments as documented in this practice is to improve the corrosion resistance of metallic surgical implants including, but not limited to, those manufactured from iron, cobalt, nickel, titanium, and tantalum base materials. 3.2 Iron particles, ceramic media, and...

ASTM C1417-19(2026) - Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
January 1, 2026 - ASTM International

This specification covers the manufacture and acceptance of reinforced concrete sewer, storm drain, and culvert pipe designed to conform to the owner's design requirements and to equivalent design specification. The reinforced concrete shall consist of cementitious materials; mineral aggregates;...

ASTM C1417M-19(2026) - Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
January 1, 2026 - ASTM International

This specification covers the manufacture and acceptance of reinforced concrete sewer, storm drain, and culvert pipe designed to conform to the owner's design requirements and to equivalent design specification. The reinforced concrete shall consist of cementitious materials; mineral aggregates;...

ASTM A414/A414M-25a - Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels
December 1, 2025 - ASTM International

This specification covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Tensile and yield strengths shall be determined after a tension test of the sheets. The material shall be furnished without removing the hot-rolled oxide or scale. When required, the...

ASTM C231/C231M-26 - Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
January 1, 2026 - ASTM International

1.1 This test method covers determination of the air content of freshly mixed concrete from observation of the change in volume of concrete with a change in pressure. 1.2 This test method is intended for use with concretes and mortars made with relatively dense aggregates for which the aggregate...

ASTM D6155-19(2025) - Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures
December 1, 2025 - ASTM International

1.1 This specification covers the use of coarse aggregates not traditionally used in asphalt paving mixtures. These nontraditional aggregates can be described as any aggregate other than those described in Specifications D692/D692M, D693, D1139/D1139M, and D5106 (crushed stone, crushed hydraulic...

ASTM C685/C685M-25a - Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing
December 15, 2025 - ASTM International

This specification covers concrete made by volumetric batching and continuous mixing. Requirements for quality of concrete shall be either as hereinafter specified or as specified by the purchaser. When the requirements of the purchaser differ from this specification, the purchaser's specification...

ASTM C1556-25 - Standard Test Method for Determining the Apparent Chloride Diffusion Coefficient of Cementitious Mixtures by Bulk Diffusion
November 1, 2025 - ASTM International

5.1 This test method is applicable to cementitious mixtures that have not been exposed to external chloride ions, other than the negligible quantity of chloride ion exposure from sample preparation using potable water, prior to the test. 5.2 The calculation procedure described in this test method...

ASTM C231/C231M-25 - Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
October 15, 2025 - ASTM International

1.1 This test method covers determination of the air content of freshly mixed concrete from observation of the change in volume of concrete with a change in pressure. 1.2 This test method is intended for use with concretes and mortars made with relatively dense aggregates for which the aggregate...

ASTM A414/A414M-25 - Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels
September 1, 2025 - ASTM International

This specification covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Tensile and yield strengths shall be determined after a tension test of the sheets. The material shall be furnished without removing the hot-rolled oxide or scale. When required, the...

ASTM C655-19a(2025) - Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
September 1, 2025 - ASTM International

This specification covers reinforced concrete pipe, D-load culvert, storm drain, and sewer pipe for the conveyance of sewage, industrial wastes, and storm water. The numerical values in this specification are not presented in inch-pound units, but rather, in metric or SI units only. The reinforced...

ASTM C655M-19a(2025) - Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)
September 1, 2025 - ASTM International

This specification covers reinforced concrete pipe, D-load culvert, storm drain, and sewer pipe for the conveyance of sewage, industrial wastes, and storm water. The numerical values in this specification are not presented in inch-pound units, but rather, in metric or SI units only. The reinforced...

ASTM C76-25 - Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
September 1, 2025 - ASTM International

This specification covers reinforced concrete culvert, storm drain, and sewer pipe. The pipe manufactured with this specification shall be of five classes: Class I, Class II, Class III, Class IV, and Class V. The strength requirements for each class are specified. The reinforced concrete shall...

Advertisement