loading
ASTM D6279-26 - Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings
June 1, 2026 - ASTM International

5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning and exposure) during manufacture and service that can mar their surface. The ability of high gloss coatings to maintain their...

ASTM D6037-26 - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
June 1, 2026 - ASTM International

5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning, and exposure) that can mar their surface. The ability of these coatings to maintain their appearance is an important product...

ASTM F2460-25 - Standard Practice for Special Requirements for Bumper Boats
October 1, 2025 - ASTM International

1.1 This practice establishes criteria for the design, manufacture, and operations of bumper boats. These are boats used to bump into each other intentionally as directed by drivers as a form of entertainment. Boats are fitted with an inflatable or impact attenuating device to...

ASTM F3052-14(2025) - Standard Guide for Conducting Small Boat Stability Test (Deadweight Survey and Air Inclining Experiment) to Determine Lightcraft Weight and Centers of Gravity of a Small Craft
October 1, 2025 - ASTM International

4.1 From the lightcraft characteristics, calculations of the stability characteristics of the small craft for all load conditions can determine compliance to applicable stability criteria or provide mass properties information for other analyses or investigations. Accurate results from an air...

ASTM E1201-25 - Standard Practice for Sampling Zooplankton with Conical Tow Nets
September 1, 2025 - ASTM International

5.1 The advantages of using conical tow nets are as follows: 5.1.1 They are relatively inexpensive and highly versatile in a variety of inland, estuarine, coastal, and marine waters. 5.1.2 They can be used from a small or large powered boat with a minimum of auxiliary equipment. 5.1.3 They...

ASTM D4330-24 - Standard Practice for Evaluation of Fiberglass Boat Polish and Wax
November 1, 2024 - ASTM International

3.1 Boat polish or wax aids in cleaning and maintaining the surface of fiberglass boats. The function of cleaning is very important. 3.2 This practice defines the properties to be tested, the apparatus to use, and the comparisons of product performance. It is recognized that...

ASTM C1607-12(2025) - Standard Test Method for Determination of "Microwave Safe for Reheating" for Ceramicware
June 1, 2025 - ASTM International

5.1 This test method is for evaluating ceramic products that are intended for reheating in a Consumer based microwave oven. It is not intended for evaluating products that will be used in commercial type microwaves. 5.2 This test method is not intended to evaluate metallic or polymeric based...

ASTM F3431-25 - Standard Specification for Determining Flammability of Materials for Recreational Camping Tents and Warning Labels for Associated Hazards
April 1, 2025 - ASTM International

1.1 This specification covers requirements and contains test methods for outdoor recreational camping tents for persons. These requirements include controlled small flame test methods for materials used to manufacture tents. The requirements are intended to specify materials that do not present an...

ASTM F3680-24 - Standard Practice for Parasail Labeling and Accompanying Literature
October 1, 2024 - ASTM International

1.1 This practice sets forth labeling and instruction guidelines for manufacturers of parasails for boat launch and recovery and beach launch and recovery. 1.2 This practice applies only to parasails that are used under Practice F3099 and other ASTM standards pertaining to parasailing only....

ASTM D5762-24 - Standard Test Method for Nitrogen in Liquid Hydrocarbons, Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence
July 1, 2024 - ASTM International

5.1 Many nitrogen compounds can contaminate refinery catalysts. They tend to be the most difficult class of compounds to hydrogenate, so the nitrogen content remaining in the product of a hydrotreater is a measure of the effectiveness of the hydrotreating process. In lubricating oils the...

ASTM D6759-24 - Standard Practice for Sampling Liquids Using Grab and Discrete Depth Samplers
June 1, 2024 - ASTM International

4.1 Sampling at specified depth(s) within a liquid may be needed to confirm or rule out variations within a target population. This practice describes the design and operation of commercially available grab and discrete depth samplers for persons responsible for designing or implementing sampling...

UL 2034 - Single and Multiple Station Carbon Monoxide Alarms
June 3, 2024 - ULSE

1.1 These requirements cover electrically operated single and multiple station carbon monoxide (CO) alarms intended for protection in ordinary indoor locations and unconditioned areas, per applicable governing laws, codes, and standards. This includes, but is not limited to, of dwelling units,...

ASTM F1739-96(2024) - Standard Guide for Performance of a Water Rescuer—Level I
April 1, 2024 - ASTM International

1.1 This guide covers minimum requirements for the scope of performance of a water rescuer I who may be responsible for the initial on-scene evaluation, performing land-based water rescues, and providing initial patient care at a water rescue incident. 1.2 This guide is one in a series; water...

UL 2700 - Sustainability for Cleaning and Cleaning Related Products
December 12, 2023 - ULSE

2.1 This Standard establishes general requirements for human health and environmental criteria for industrial, institutional, and consumer cleaning and cleaning-related products such as but not limited to: a) Hard Surface Cleaners: 1) Bathroom cleaners (Non-Disinfecting); 2) Boat and bilge...

J1204_202312 - Wheels - Recreational and Utility Trailer Fatigue Test Procedure and Performance Requirements
December 7, 2023 - SAE International

This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway service on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose...

ASTM F1074-87(2023) - Standard Specification for Cleats, Welded Horn Type
July 1, 2023 - ASTM International

1.1 This specification covers hollow cleats and pads for marine use. 1.2 The cleats shall be used where securing of boat handling lines are required onboard commercial and navy boats and crafts. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given...

ASTM F2291-23b - Standard Practice for Design of Amusement Rides and Devices
September 1, 2023 - ASTM International

1.1 This practice establishes criteria for the design of amusement rides, devices and major modifications to amusement rides and devices manufactured after the effective date of publication except as noted in 1.2. 1.2 This practice shall not apply to: 1.2.1 Patron directed amusement rides or...

AIR1899A - Aerospace Military Aircraft Hydraulic System Characteristics
April 26, 2023 - SAE International

This SAE Aerospace Information Report (AIR) has been compiled to provide information on hydraulic systems fitted to the following categories of military vehicles. Attack Airplanes Fighter Airplanes Bombers Anti-Sub, Fixed Wing Airplanes Transport Airplanes Helicopters Boats

ASTM F956-91(2023) - Standard Specification for Bell, Cast, Sound Signalling
May 1, 2023 - ASTM International

This specification covers cast sound-signalling bells, together with bulkhead mounting plates for the smaller bells, for use on ships, boats, and other marine craft, for compliance with the rules in the convention on the International Regulations for Preventing Collisions at Sea. Bell...

ASTM F2291-23a - Standard Practice for Design of Amusement Rides and Devices
August 1, 2023 - ASTM International

1.1 This practice establishes criteria for the design of amusement rides, devices and major modifications to amusement rides and devices manufactured after the effective date of publication except as noted in 1.2. 1.2 This practice shall not apply to: 1.2.1 Patron directed amusement rides or...

Advertisement