loading
ASTM F3125/F3125M-26 - Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi, 144 ksi, and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength
July 1, 2026 - ASTM International

This specification provides the chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch and metric dimensions, in two strength grades, two types and two styles. It is intended to ensure alignment between standards with...

ASTM F2836-26 - Standard Practice for Gasket Constants for Bolted Joint Design
June 1, 2026 - ASTM International

5.1 This practice determines the room temperature gasket constants Gb and a for initial seating and Gs for operating conditions as related to the tightness behavior of pressurized bolted flanged connections. These constants are used in determining the design bolt load for gasketed...

ASTM A1014/A1014M-26 - Standard Specification for Precipitation-Hardening Bolting (UNS N07718) for High Temperature Service
July 1, 2026 - ASTM International

1.1 This specification covers precipitation hardening bolting material (UNS N07718) and bolting components for high temperature service. See Specification A962/A962M for the definition of "bolting." 1.2 The following referenced general requirements are indispensable for...

ASTM A1082/A1082M-26 - Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications
July 1, 2026 - ASTM International

1.1 This specification covers high strength stainless steel bolting materials and bolting components for special purpose applications such as pressure vessels. Several grades of precipitation-hardened and duplex (ferritic-austenitic) stainless steels are covered. Selection will depend...

ASTM F432-19(2026) - Standard Specification for Roof and Rock Bolts and Accessories
May 1, 2026 - ASTM International

This specification covers the chemical, mechanical, and dimensional requirements for roof and rock bolts and accessories. Addressed in this specification are double-end threaded and slotted steel bars; fully grouted bolts and threaded bars; mechanical anchorage devices used for point...

ASTM D7853-13(2026) - Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete
June 1, 2026 - ASTM International

5.1 Due to hydraulic pressure that may be present on some applications, engineers need to understand the capability of these products to resist this pressure. This test allows engineers to compare products and verify pullout strength. 5.2 Hydraulic pullout resistance is a function of locking...

ASTM E1685-20(2026) - Standard Practice for Measuring the Change in Length of Bolts Using the Ultrasonic Pulse-Echo Technique
April 1, 2026 - ASTM International

1.1 This practice covers a procedure for measuring changes in length of threaded bolts using the ultrasonic pulse-echo technique. 1.2 This procedure is normally intended for metal bolting 6.3 mm or more in nominal diameter with effective length-to-diameter ratios of 2:1 or greater. 1...

ASTM G168-26 - Standard Practice for Making and Using Precracked Double Beam Stress Corrosion Specimens
May 1, 2026 - ASTM International

5.1 Precracked specimens offer the opportunity to use the principles of linear elastic fracture mechanics (1) to evaluate resistance to stress corrosion cracking in the presence of a pre-existing crack. This type of evaluation is not included in conventional bent beam, C-ring, U-bend, and tension...

ASTM F959/F959M-26 - Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series
March 1, 2026 - ASTM International

This specification covers the requirements for two types (Types 8.8 and 10.9) of compressible-washer-type direct tension indicators, in nominal diameter sizes M16 through M36, capable of indicating the achievement of a specified minimum bolt tension in a structural bolt and are...

ASTM E329-26 - Standard Specification for Agencies Engaged in Construction Inspection, Testing, or Special Inspection
June 1, 2026 - ASTM International

1.1 This specification defines the minimum requirements for agencies engaged in any of the following: (a) Inspection of specified methods and materials used in construction, (b) Special inspection, and (c) Testing of materials used in construction. 1.2 Criteria are provided for assessing the...

ASTM A354-26 - Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
March 1, 2026 - ASTM International

This specification covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners. All fasteners shall be made from alloy steel conforming to the chemical composition requirements. Two levels of bolting...

ASTM A962/A962M-26 - Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
February 1, 2026 - ASTM International

1.1 This specification covers a group of common requirements that shall apply to carbon, alloy, stainless steel, and nickel alloy bolting under any of the following ASTM Specifications (or under any other ASTM Specifications that invoke this specification or portions thereof): Title of...

ASTM A437/A437M-26 - Standard Specification for Stainless and Alloy-Steel Turbine-Type Bolting Specially Heat Treated for High-Temperature Service
February 1, 2026 - ASTM International

1.1 This specification covers stainless and alloy-steel bolting material and bolting components specially heat treated for high-temperature service, such as steam turbine, gas turbine, and similar uses. See Specification A962/A962M for the definition of bolting. This material...

ASTM A529/A529M-26 - Standard Specification for High-Strength Carbon-Manganese Steel of Structural Quality
April 1, 2026 - ASTM International

1.1 This specification covers carbon-manganese steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of buildings and for general structural purposes. 1.2 Material under this specification is available in two grades: Grade Yield Strength, ksi...

ASTM E328-26 - Standard Test Methods for Stress Relaxation for Materials and Structures
April 1, 2026 - ASTM International

5.1 Stress-relaxation test data are necessary when designing most mechanically fastened joints to ensure the permanent tightness of bolted or riveted assemblies, press or shrink-fit components, rolled-in tubes, etc. Other applications include predicting the decrease in the tightness of...

ASTM A453/A453M-26 - Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels
February 1, 2026 - ASTM International

1.1 This specification covers five grades of bolting materials with twelve classes of yield strength ranging from 50 to 120 ksi [345 to 825 MPa] for use in high-temperature service for bolting components, such as bolts, screws, nuts, or studs, for pressure vessel and valve...

ASTM B490-09(2026) - Standard Practice for Micrometer Bend Test for Ductility of Electrodeposits
February 1, 2026 - ASTM International

4.1 This practice is useful as one method of controlling some electroplating solutions. It serves to indicate the presence of contamination or some other adverse condition. 4.2 Ductility measurements are of particular value when electroplated parts are to be subjected to moderate stress such as...

ASTM F468-23(2026) - Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
March 1, 2026 - ASTM International

This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs manufactured from a number of alloys in common use and intended for general service applications. The bolts, cap screws, and studs shall be manufactured from material having a...

ASTM A193/A193M-26 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
February 1, 2026 - ASTM International

1.1 This specification covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of...

ASTM A540/A540M-26 - Standard Specification for Alloy-Steel Bolting for Special Applications
February 1, 2026 - ASTM International

1.1 This specification covers regular and special-quality alloy steel bolting materials and bolting components that may be used for nuclear and other special applications. See Specification A962/A962M for the definition of bolting. 1.2 The following referenced common...

Advertisement