This specification covers two grades of burner fuel consisting of triglycerides and naturally occurring constituents of triglycerides including monoglycerides, diglycerides, and free fatty acids and distinguished by the pour point. The triglyceride burner fuels, Grade TBF5 and Grade...
5.1 This test method is intended for use when measuring surface flammability of flexible cellular materials exposed to fire. The test method provides a laboratory test procedure for measuring and comparing the surface flammability of materials when exposed to a prescribed level of radiant heat...
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows: 1.1.1 Grades No. 1 of all sulfur grades and No. 2 of all sulfur grades are middle...
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows: 1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2...
4.1 This test method describes the procedure to evaluate or compare, or both, the durability of sealants when subjected to accelerated weathering and cyclic movement in a joint. 4.2 Sealant installation procedures, design considerations and movement during cure affect the aging processes and are...
This specification covers heavy-duty ranges that use gas or electrical heat sources, or both, for cooking food in the commercial and institutional food service establishments. Types: type I-electric range top with electric oven; type I-electric range top with gas-fired oven; type I-electric range...
1.1 This practice covers the testing of the performance of a flame ionization detector (FID) used as the detection component of a gas or supercritical fluid (SF) chromatographic system. 1.2 This recommended practice is directly applicable to an FID that employs a hydrogen-air or hydrogen-oxygen...
1.1 This test method covers the estimation of the gross and net heat of combustion in SI units, megajoules per kilogram, of hydrocarbon fuels and blendstocks from the fuel density and sulfur, water, and ash contents. 1.1.1 This test method is not applicable to fuels containing non-hydrocarbons such...
1.1 This test method2 covers the manual determination of nitrogen dioxide (NO2) in the atmosphere in the range from 4?μg/m3 to 10 000 μg/m3 (0.002 ppm(v) to 5 ppm(v)) when sampling is conducted in fritted-tip bubblers. 1.2 For concentrations of NO2 in excess of 10 mg/m3 (5?ppm(v)), as occur in...
1.1 This specification (see Note 1) covers grades of fuel oil intended for use in various types of fuel-oil-burning equipment under various climatic and operating conditions. These grades are described as follows: 1.1.1 Grades No. 1 S5000, No. 1 S500, No. 1 S15, No. 2 S5000, No. 2 S500, and No. 2...
1.1 This is a fire-test-response standard. 1.2 This fire test method is applicable to the electrical insulation materials contained in wires or cables. 1.3 The ignition source is a gas burner fueled by methane or natural gas. 1.4 Use the values stated in SI units in referee decisions; see...
1.1 This is a fire-test-response standard. 1.2 This fire test method is applicable to electrical insulation materials used for wires or cables. The materials are tested as plastic specimens on their own or installed on the wires or cables. 1.3 The ignition source is a gas burner fueled by...
5.1 The expanded limits of the Adjunct for VCF are defined in a mixture of terms of customary and metric units. Table 1 shows the defining limits and their associated units in bold italics. Also shown in Table 1 are the limits converted to their equivalent units (and, in the case of the densities,...
5.1 This test method provides a means of measuring a variety of fire-test-response characteristics resulting from burning a stack of five stacking chairs. After ignition using a propane gas burner, the test specimen is permitted to burn freely under well-ventilated conditions. The most...
1.1 This test method measures the performance of the perimeter fire barrier and its ability to maintain a seal to prevent fire spread during the deflection and deformation of the exterior wall assembly and floor assembly during the fire test, while resisting fire exposure from an interior...
1.1 This test method measures the performance of the perimeter fire barrier and its ability to maintain a seal to prevent fire spread during the deflection and deformation of the exterior wall assembly and floor assembly during the fire test, while resisting fire exposure from an interior...
Note 1: This description of the features of a Fuel-Burning Portable Device which is within the scope of this standard, together with the exceptions listed, are intended to identify device configurations that have been shown a risk of flame jetting. See X1.2. 1.1 These requirements apply to devices...
5.1 The carbon residue value of burner fuel serves as a rough approximation of the tendency of the fuel to form deposits in vaporizing pot-type and sleeve-type burners. Similarly, provided alkyl nitrates are absent (or if present, provided the test is performed on the base fuel...
1.1 This specification covers two grades of kerosine suitable for use in critical kerosine burner applications: 1.1.1 No. 1-K-A special low-sulfur grade kerosine suitable for use in nonflue-connected kerosine burner appliances and for use in wick-fed illuminating lamps. 1.1.2 No....
1.1 This practice covers general considerations for the quantitative determination of elements in water and waste water by flame atomic absorption spectrophotometry. Flame atomic absorption spectrophotometry is simple, rapid, and applicable to a large number of elements in drinking water, surface...
Narrow Your Results