This comprehensive review of calibration provides an excellent foundation for understanding principles and applications of the most frequently performed tasks of a technician. Topics addressed include terminology, bench vs. field calibration, loop vs. individual instrument...
1.1 This test method describes the temperature calibration of a dynamic mechanical analyzer using thermal lag over the temperature range of -100 °C to 300 °C. 1.2 This standard may be compared to Test Methods E1867. 1.3 The values stated in SI units are to be regarded as standard. No other...
1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform...
1.1 This test method is intended for calibration and characterization of primary terrestrial photovoltaic reference cells to a desired reference spectral irradiance distribution, such as Tables G173. The recommended physical requirements for these reference cells are described in...
4.1 Standards such as ISO 11137-1 for radiation sterilization of healthcare products and ISO 14470 for irradiation of food state that dosimetry used in the process's development, validation, and routine control adhere to specific requirements. These requirements state that the dosimetry must be...
1.1 This test method covers the energy dispersive X-ray fluorescence (EDXRF) spectrochemical analysis of trace levels of uranium and thorium in soils. Any sample matrix that differs from the general ground soil composition used for calibration (that is, fertilizer or a sample of mostly rock)...
4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...
1.1 This practice covers instruction for determining the density calibration of X- and ?-ray computed tomography (CT) systems and for using this information to measure different material densities from CT images. The calibration is based on an examination of the CT image of a disk of...
4.1 This practice is applicable to the use of calorimetric dosimetry systems for the measurement of absorbed dose in electron beams, the qualification of electron irradiation facilities, periodic checks of the performance of electron irradiation facilities, and calibration of other dosimetry...
5.1 Cotton fiber that is on average finer and more mature is more desirable than coarse or immature fiber, although distinction between these qualities cannot be made quickly and accurately using current test methods. Immature fibers break more easily during processing and have a tendency to form...
1.1 This test method covers the identification and simultaneous measurement of purgeable volatile organic compounds. It has been validated for treated drinking water, wastewater, and ground water. This test method is not limited to these particular aqueous matrices; however, the applicability of...
5.1 This test method provides guidelines and basic test methods for the accuracy verification of infrared thermometers. It includes test set-up and calculation of uncertainties. It is intended to provide the user with a consistent method, while remaining flexible in the choice of calibration...
1.1 This test method covers a procedure which is used to measure the surface area of precipitated hydrated silicas by the conventional Brunauer, Emmett, and Teller (BET) theory of multilayer gas adsorption behavior using multipoint determinations, similar to that used for carbon black in Test...
1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure after...
5.1 The methods described represent the preferable means for calibration of field radiometers employing standard reference radiometers. Other methods involve the employment of an optical bench and essentially a point source of artificial light. While these methods are useful for cosine and...
1.1 This test method covers the determination of the fineness of hydraulic cement by means of the 45-μm (No. 325) sieve. 1.1.1 This test method may be used for the determination of the fineness of other materials. However, certain requirements, such as calibration procedures, cleaning of...
1.1 This test method covers the liquid chromatography tandem mass spectrometry (LC-MS/MS) detection and quantitation of N-nitrosamines after direct injection. It has been validated for groundwater, surface water, wastewater influents, and wastewater effluents. This test method is not limited to...
4.1 General-Most thickness gauges are not applicable to all combinations of coating-substrate thicknesses and materials. The limitations of a particular instrument are generally delineated by its manufacturer. The substrate material and coating combination to be measured as well as the inherent...
1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
4.1 The test method was developed for determining the fracture resistance of asphalt mixtures. The fracture resistance can help differentiate asphalt mixtures whose service life might be compromised by cracking. The test method is generally valid for specimens that are tested at temperatures of...
Narrow Your Results