loading
ISA CALIBRATION: A TECHNI - Calibration: A Technician's Guide
January 1, 2005 - ISA

This comprehensive review of calibration provides an excellent foundation for understanding principles and applications of the most frequently performed tasks of a technician. Topics addressed include terminology, bench vs. field calibration, loop vs. individual instrument...

ASTM E3301-26 - Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers Using Thermal Lag
July 1, 2026 - ASTM International

1.1 This test method describes the temperature calibration of a dynamic mechanical analyzer using thermal lag over the temperature range of -100 °C to 300 °C. 1.2 This standard may be compared to Test Methods E1867. 1.3 The values stated in SI units are to be regarded as standard. No other...

ASTM E74-18(2026) - Standard Practices for Calibration and Verification for Force-Measuring Instruments
April 1, 2026 - ASTM International

1.1 The purpose of these practices is to specify procedures for the calibration of force-measuring instruments. Procedures are included for the following types of instruments: 1.1.1 Elastic force-measuring instruments, and 1.1.2 Force-multiplying systems, such as balances and small platform...

ASTM E1125-16(2026) - Standard Test Method for Calibration of Primary Non-Concentrator Terrestrial Photovoltaic Reference Cells Using a Tabular Spectrum
June 1, 2026 - ASTM International

1.1 This test method is intended for calibration and characterization of primary terrestrial photovoltaic reference cells to a desired reference spectral irradiance distribution, such as Tables G173. The recommended physical requirements for these reference cells are described in...

ASTM ASTM51261-26 - Standard Practice for Calibration of Routine Dosimetry Systems for Radiation Processing
May 1, 2026 - ASTM International

4.1 Standards such as ISO 11137-1 for radiation sterilization of healthcare products and ISO 14470 for irradiation of food state that dosimetry used in the process's development, validation, and routine control adhere to specific requirements. These requirements state that the dosimetry must be...

ASTM C1255-26 - Standard Test Method for Analysis of Uranium and Thorium in Soils by Energy Dispersive X-Ray Fluorescence Spectroscopy
July 1, 2026 - ASTM International

1.1 This test method covers the energy dispersive X-ray fluorescence (EDXRF) spectrochemical analysis of trace levels of uranium and thorium in soils. Any sample matrix that differs from the general ground soil composition used for calibration (that is, fertilizer or a sample of mostly rock)...

ASTM D6752/D6752M-26 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
August 1, 2026 - ASTM International

4.1 The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test Method D3203, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction. 4.2 Since specific gravity has...

ASTM E1935-26 - Standard Practice for Calibrating and Measuring CT Density
June 15, 2026 - ASTM International

1.1 This practice covers instruction for determining the density calibration of X- and ?-ray computed tomography (CT) systems and for using this information to measure different material densities from CT images. The calibration is based on an examination of the CT image of a disk of...

ASTM ASTM51631-26 - Standard Practice for Use of Calorimetric Dosimetry Systems for Dose Measurements and Routine Dosimetry System Calibration in Electron Beams
May 1, 2026 - ASTM International

4.1 This practice is applicable to the use of calorimetric dosimetry systems for the measurement of absorbed dose in electron beams, the qualification of electron irradiation facilities, periodic checks of the performance of electron irradiation facilities, and calibration of other dosimetry...

ASTM D8394-21(2026) - Standard Test Method for Automated Measurement of Maturity, Fineness, Ribbon Width, and Micronaire of Cotton Fibers
July 1, 2026 - ASTM International

5.1 Cotton fiber that is on average finer and more mature is more desirable than coarse or immature fiber, although distinction between these qualities cannot be made quickly and accurately using current test methods. Immature fibers break more easily during processing and have a tendency to form...

ASTM D5790-18(2026) - Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry
July 1, 2026 - ASTM International

1.1 This test method covers the identification and simultaneous measurement of purgeable volatile organic compounds. It has been validated for treated drinking water, wastewater, and ground water. This test method is not limited to these particular aqueous matrices; however, the applicability of...

ASTM E2847-21(2026) - Standard Test Method for ? ?Calibration and Accuracy Verification of Wideband Infrared Thermometers
April 1, 2026 - ASTM International

5.1 This test method provides guidelines and basic test methods for the accuracy verification of infrared thermometers. It includes test set-up and calculation of uncertainties. It is intended to provide the user with a consistent method, while remaining flexible in the choice of calibration...

ASTM D1993-22(2026) - Standard Test Method for Precipitated Silica-Surface Area by Multipoint BET Nitrogen Adsorption
July 1, 2026 - ASTM International

1.1 This test method covers a procedure which is used to measure the surface area of precipitated hydrated silicas by the conventional Brunauer, Emmett, and Teller (BET) theory of multilayer gas adsorption behavior using multipoint determinations, similar to that used for carbon black in Test...

ASTM C336-26 - Standard Test Method for Annealing Point and Strain Point of Glass by Fiber Elongation
July 1, 2026 - ASTM International

1.1 This test method covers the determination of the annealing point and the strain point of a glass by measuring the viscous elongation rate of a fiber of the glass under prescribed condition. 1.2 The annealing and strain points shall be obtained by following the specified procedure after...

ASTM E824-26 - Standard Test Method for Transfer of Calibration From Reference to Field Radiometers
March 1, 2026 - ASTM International

5.1 The methods described represent the preferable means for calibration of field radiometers employing standard reference radiometers. Other methods involve the employment of an optical bench and essentially a point source of artificial light. While these methods are useful for cosine and...

ASTM C430-26 - Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the fineness of hydraulic cement by means of the 45-μm (No. 325) sieve. 1.1.1 This test method may be used for the determination of the fineness of other materials. However, certain requirements, such as calibration procedures, cleaning of...

ASTM D8456-26 - Standard Test Method for Determination of Nitrosamines in Water by Liquid Chromatography Tandem Mass Spectrometry (LC-MS/MS)
July 1, 2026 - ASTM International

1.1 This test method covers the liquid chromatography tandem mass spectrometry (LC-MS/MS) detection and quantitation of N-nitrosamines after direct injection. It has been validated for groundwater, surface water, wastewater influents, and wastewater effluents. This test method is not limited to...

ASTM E376-26 - Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy Current (Electromagnetic) Testing Methods
July 1, 2026 - ASTM International

4.1 General-Most thickness gauges are not applicable to all combinations of coating-substrate thicknesses and materials. The limitations of a particular instrument are generally delineated by its manufacturer. The substrate material and coating combination to be measured as well as the inherent...

ASTM D7237-18(2026) - Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection
July 15, 2026 - ASTM International

1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...

ASTM D7313-20(2026) - Standard Test Method for Determining Fracture Energy of Asphalt Mixtures Using the Disk-Shaped Compact Tension Geometry
July 1, 2026 - ASTM International

4.1 The test method was developed for determining the fracture resistance of asphalt mixtures. The fracture resistance can help differentiate asphalt mixtures whose service life might be compromised by cracking. The test method is generally valid for specimens that are tested at temperatures of...

Advertisement