loading
ATIS CARS-007 - Ordering and Billing Forum (OBF) CABS (Carrier Access Billing System) Auxiliary Report Specifications
January 1, 2004 - ATIS

The CABS Auxiliary Report Specifications (CARS) are guidelines for providing standard reports and/or standard mechanized file layouts, where appropriate. These standards will not be documented in the CABS Billing Output Specifications (BOS). The following guidelines apply to report outputs...

ATIS CARS-006 - Ordering and Billing Forum (OBF) CABS (Carrier Access Billing System) Auxiliary Report Specifications
March 1, 2003 - ATIS

The CABS Auxiliary Report Specifications (CARS) are guidelines for providing standard reports and/or standard mechanized file layouts, where appropriate. These standards will not be documented in the CABS Billing Output Specifications (BOS). The following guidelines apply to report outputs...

IEEE CAREERS FOR - CAREERS FOR ELECTRICAL ENGINEERING AND COMPUTER
IEEE
A description is not available for this item.
ASTM CARBON - ASTM STANDARDS ON ACTIVATED CARBON 2ND EDITION
ASTM
A description is not available for this item.
PCMCIA CARDWARE SDK - CARDWARE SDK
PCMCIA
A description is not available for this item.
AIHA CAREERWORKS - CAREERWORKS AND CAREERWORKS FOR KIDS
AIHA
A description is not available for this item.
PCMCIA CARDBUS SYSTEM - PCMCIA CARDBUS SYSTEM ARCHITECTURE
PCMCIA
A description is not available for this item.
ASTM D2847-22(2026) - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
August 1, 2026 - ASTM International

1.1 This practice covers an updated procedure for evaluating corrosion protection and performance of an engine coolant in passenger car, light truck service that closely imitates current vehicle and engine manufacturers' practices. Note 1: Coolant evaluation in vehicle service may require...

ASTM F3067-26 - Standard Guide for Radial Loading of Balloon-Expandable and Self-Expanding Vascular Stents
May 1, 2026 - ASTM International

4.1 Upon deployment, at the site of the vascular stenosis, the stent establishes the patency of the lumen until vascular remodeling occurs. The radial load acting upon the stent is imparted by vessel and lesion stretch. Additionally, the vessel might be affected by excursions due to pulsation...

ASTM D1900-25 - Standard Practice for Carbon Black—Sampling Bulk Shipments
December 15, 2025 - ASTM International

1.1 This practice covers procedures for the sampling and data reporting of bulk shipments of carbon black in three-compartment hopper rail cars and compartmented bulk hopper trailers. Note 1: The tests to be made on the samples obtained by this practice, how many samples are taken, where...

ASTM F3361-18(2025) - Standard Guide for Classifying Alterations for In-Service Aircraft under FAA Authority Oversight
November 1, 2025 - ASTM International

1.1 This guide is intended for Part 23 and predecessor aircraft (see Civil Air Regulations (CAR) 3) and: 1.1.1 Is applicable to aircraft to which Part 43 applies. 1.1.2 Addresses both initial installation and replacement of aircraft articles. 1.1.3 Is a guide for classifying an alteration. 1...

ASTM D5728-25 - Standard Practices for Securement of Cargo in Intermodal and Unimodal Surface Transport
October 1, 2025 - ASTM International

1.1 These practices are intended to serve as a guide to shippers, carriers, and consignees for load planning, loading, blocking, and bracing of intermodal and unimodal cargo in surface transport. The practices are referenced to a bibliography of information concerning the above. Hazardous...

ASTM F2838-25 - Standard Practice for Accelerated Laboratory Aging of Radial Passenger Car and Light Truck Tires through Load Range E for the Laboratory Generation of Belt Separation
August 1, 2025 - ASTM International

1.1 This practice describes a method to laboratory age a new tire in an oven to produce changes in certain chemical and physical properties at the belt edges similar to those of tires in-service (see Appendix X1). 1.2 This practice is a precursor to conducting an ASTM standard roadwheel test method...

ASTM D5414-95(2025) - Standard Test Method for Evaluation of Horizontal Impact Performance of Load Unitizing Stretch Wrap Films
August 1, 2025 - ASTM International

5.1 This test method is intended to be used mainly as a means of comparing the performance of unitizing films. It can also be used to compare the effectiveness of different wrap cycles with the same wrapping materials. No direct correlation between these tests results and actual field performance...

ASTM D4583-21(2025) - Standard Practice for Carbon Black—Calculation of Process Indexes From an Analysis of Process Control Data
September 1, 2025 - ASTM International

1.1 This practice covers (1) a statistical procedure for analyzing the test data generated in the statistical process control of a carbon black manufacturing process; (2) a format for reporting process capability determined from the analysis of control chart data of an individual production run,...

Advertisement