loading
ASTM B930-03(2026) - Standard Test Method for Rating Grain Size and Frequency of Abnormally Large Grains in Cemented Tungsten Carbides (Hardmetals)
July 1, 2026 - ASTM International

1.1 This test method describes a procedure for measuring abnormally large grains and the frequency of those grains in cemented tungsten carbides (hardmetals). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility...

ASTM B276-21(2026) - Standard Test Method for Apparent Porosity in Cemented Carbides
July 1, 2026 - ASTM International

1.1 This test method specifies procedures for the metallographic determination of apparent porosity in cemented carbides. Note 1: The term "apparent porosity" is construed to mean all microstructures observed on a properly prepared, unetched surface, including structures resulting from...

ASTM B663/B663M-26 - Standard Specification for Silver-Tungsten Carbide Electrical Contact Material
February 1, 2026 - ASTM International

This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures. This specification covers compositions within the silver-tungsten carbide system. The material shall conform to composition limits. Chemical analysis shall be...

ASTM C1457-26 - Standard Test Method for Determination of Total Hydrogen Content of Uranium Oxide Powders and Pellets by Carrier Gas Extraction
July 1, 2026 - ASTM International

1.1 This test method applies to the determination of hydrogen in nuclear-grade uranium oxide powders and pellets to determine compliance with specifications. Gadolinium oxide (Gd2O3) and gadolinium oxide-uranium oxide powders and pellets may also be analyzed using this test method. 1.2 This...

ASTM C1274-12(2026) - Standard Test Method for Advanced Ceramic Specific Surface Area by Physical Adsorption
July 15, 2026 - ASTM International

1.1 This test method covers the determination of the surface area of advanced ceramic materials (in a solid form) based on multilayer physisorption of gas in accordance with the method of Brunauer, Emmett, and Teller (BET) (1) and based on IUPAC Recommendations (1984 and 1994) (2, 3). This test...

ASTM B761-26 - Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
May 1, 2026 - ASTM International

1.1 This test method covers the determination of particle size distributions of metal powders. Experience has shown that this test method is satisfactory for the analysis of elemental tungsten, tungsten carbide, molybdenum, and tantalum powders, all with an as-supplied estimated average...

ASTM B614-26 - Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
April 1, 2026 - ASTM International

This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. Grease,...

ASTM B528-16(2026) - Standard Test Method for Transverse Rupture Strength of Powder Metallurgy (PM) Specimens
March 1, 2026 - ASTM International

1.1 This test method covers determination of the transverse rupture strength of sintered, including post-treated, powder metallurgy test specimens by subjecting them to a uniformly increasing transverse force under controlled conditions. The term "transverse rupture strength" as used herein,...

ASTM A193/A193M-26 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
February 1, 2026 - ASTM International

1.1 This specification covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting. Bars...

ASTM C637-26 - Standard Specification for High-Density Aggregates for Concrete
January 1, 2026 - ASTM International

This specification covers special aggregates for use in radiation-shielding concretes in which composition or high specific gravity, or both, are of prime consideration. Aggregates covered by specification include the natural mineral aggregates of either high density or high fixed water content, or...

ASTM D4944-25a - Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester
October 1, 2025 - ASTM International

1.1 This test method outlines procedures for determining the water (moisture) content of soil by chemical reaction using calcium carbide as a reagent to react with the available water in the soil producing a gas. A measurement is made of the gas pressure produced when a specified mass of wet...

ASTM B890-25 - Standard Test Method for Determination of Metallic Constituents of Tungsten Alloys and Tungsten Hardmetals by X-Ray Fluorescence Spectrometry
September 1, 2025 - ASTM International

1.1 This test method describes a procedure for the determination of the concentration, generally reported as mass percent, of the metallic constituents of tungsten-based alloys and hardmetals utilizing wavelength dispersive X-ray fluorescence spectrometry (XRF). This test method incorporates the...

ASTM B406-96(2025) - Standard Test Method for Transverse Rupture Strength of Cemented Carbides
September 1, 2025 - ASTM International

3.1 This test method is used as a means of determining the quality of cemented carbide grade powders by measuring their sintered strength. It is performed on test specimens prepared to specified shape, dimensions, and surface finish; test specimens may be prepared from finished parts if size...

ASTM B859-21(2025) - Standard Practice for De-Agglomeration of Refractory Metal Powders and Their Compounds Prior to Particle Size Analysis
September 1, 2025 - ASTM International

1.1 This practice covers the de-agglomeration of refractory metal powders and their compounds in preparation for particle size analysis. 1.2 Experience has shown that this practice is satisfactory for the de-agglomeration of elemental tungsten, molybdenum, rhenium, and tantalum metal powders, and...

ASTM B771-11(2025) - Standard Test Method for Short Rod Fracture Toughness of Cemented Carbides
September 1, 2025 - ASTM International

1.1 This test method covers the determination of the fracture toughness of cemented carbides (KIcSR) by testing slotted short rod or short bar specimens. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This...

ASTM A763-15(2025) - Standard Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels
September 1, 2025 - ASTM International

1.1 These practices cover the following four tests: 1.1.1 Practice W-Oxalic acid etch test for detecting susceptibility to intergranular attack in stabilized ferritic stainless steels by classification of the etching structures (see Sections 3 - 10). 1.1.2 Practice X-Ferric sulfate-sulfuric acid...

ASTM E2582-21(2025) - Standard Practice for Infrared Flash Thermography of Composite Panels and Repair Patches Used in Aerospace Applications
September 1, 2025 - ASTM International

1.1 This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using flash thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with a spatially uniform light...

ASTM D968-25 - Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
May 1, 2025 - ASTM International

5.1 Silica sand produces a slower rate of abrasion for organic coatings than that provided by silicon carbide. For some types of coatings, it may also provide greater differentiation. 5.2 The abrasion resistance scales produced by the two methods differ, but the methods provide approximately...

ASTM A193/A193M-25 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
May 1, 2025 - ASTM International

1.1 This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting....

ASTM B887-25 - Standard Test Method for Determination of Coercivity (Hcs) of Cemented Carbides
February 1, 2025 - ASTM International

5.1 Measurement of coercivity provides a relative comparison of carbide grain size, binder content, and possibly carbon deficiency for a given graded carbide material or product, and may be employed as a non-destructive measurement indicating deviation from a specified norm. 5.2 This...

Advertisement