1.1 This test method describes a procedure for measuring abnormally large grains and the frequency of those grains in cemented tungsten carbides (hardmetals). 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility...
1.1 This test method specifies procedures for the metallographic determination of apparent porosity in cemented carbides. Note 1: The term "apparent porosity" is construed to mean all microstructures observed on a properly prepared, unetched surface, including structures resulting from...
This specification covers electrical contact components made from silver-tungsten carbide by powder metallurgical procedures. This specification covers compositions within the silver-tungsten carbide system. The material shall conform to composition limits. Chemical analysis shall be...
1.1 This test method applies to the determination of hydrogen in nuclear-grade uranium oxide powders and pellets to determine compliance with specifications. Gadolinium oxide (Gd2O3) and gadolinium oxide-uranium oxide powders and pellets may also be analyzed using this test method. 1.2 This...
1.1 This test method covers the determination of the surface area of advanced ceramic materials (in a solid form) based on multilayer physisorption of gas in accordance with the method of Brunauer, Emmett, and Teller (BET) (1) and based on IUPAC Recommendations (1984 and 1994) (2, 3). This test...
1.1 This test method covers the determination of particle size distributions of metal powders. Experience has shown that this test method is satisfactory for the analysis of elemental tungsten, tungsten carbide, molybdenum, and tantalum powders, all with an as-supplied estimated average...
This practice covers a cleaning and de-scaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. Grease,...
1.1 This test method covers determination of the transverse rupture strength of sintered, including post-treated, powder metallurgy test specimens by subjecting them to a uniformly increasing transverse force under controlled conditions. The term "transverse rupture strength" as used herein,...
1.1 This specification covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting. Bars...
This specification covers special aggregates for use in radiation-shielding concretes in which composition or high specific gravity, or both, are of prime consideration. Aggregates covered by specification include the natural mineral aggregates of either high density or high fixed water content, or...
1.1 This test method outlines procedures for determining the water (moisture) content of soil by chemical reaction using calcium carbide as a reagent to react with the available water in the soil producing a gas. A measurement is made of the gas pressure produced when a specified mass of wet...
1.1 This test method describes a procedure for the determination of the concentration, generally reported as mass percent, of the metallic constituents of tungsten-based alloys and hardmetals utilizing wavelength dispersive X-ray fluorescence spectrometry (XRF). This test method incorporates the...
3.1 This test method is used as a means of determining the quality of cemented carbide grade powders by measuring their sintered strength. It is performed on test specimens prepared to specified shape, dimensions, and surface finish; test specimens may be prepared from finished parts if size...
1.1 This practice covers the de-agglomeration of refractory metal powders and their compounds in preparation for particle size analysis. 1.2 Experience has shown that this practice is satisfactory for the de-agglomeration of elemental tungsten, molybdenum, rhenium, and tantalum metal powders, and...
1.1 This test method covers the determination of the fracture toughness of cemented carbides (KIcSR) by testing slotted short rod or short bar specimens. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This...
1.1 These practices cover the following four tests: 1.1.1 Practice W-Oxalic acid etch test for detecting susceptibility to intergranular attack in stabilized ferritic stainless steels by classification of the etching structures (see Sections 3 - 10). 1.1.2 Practice X-Ferric sulfate-sulfuric acid...
1.1 This practice describes a procedure for detecting subsurface flaws in composite panels and repair patches using flash thermography (FT), in which an infrared (IR) camera is used to detect anomalous cooling behavior of a sample surface after it has been heated with a spatially uniform light...
5.1 Silica sand produces a slower rate of abrasion for organic coatings than that provided by silicon carbide. For some types of coatings, it may also provide greater differentiation. 5.2 The abrasion resistance scales produced by the two methods differ, but the methods provide approximately...
1.1 This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting....
5.1 Measurement of coercivity provides a relative comparison of carbide grain size, binder content, and possibly carbon deficiency for a given graded carbide material or product, and may be employed as a non-destructive measurement indicating deviation from a specified norm. 5.2 This...
Narrow Your Results