4.1 Individual pellet hardness is related to several carbon black characteristics. Among these are mass strength and attrition. The subsequent level of dispersion obtained in some mixed compounds containing the carbon black may be affected by pellet hardness. Acceptable pellet...
1.1 This terminology covers a compilation of definitions of technical terms used in the recovered carbon black industry. Terms that are generally understood or adequately defined in other readily available sources are not included. 1.2 This international standard was developed in accordance...
4.1 The oil absorption number of a carbon black is related to the processing and vulcanizate properties of rubber compounds containing the carbon black.
1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure...
This standard covers the specifications for physical properties and performance requirements of virgin impregnated activated carbon to be used for the removal of gaseous radioiodine species from gas streams. The activated carbon furnished under this specification shall be virgin...
1.1 This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction, covered by the latest revision of ASME B16.9, ASME B16.11, MSS SP-79, MSS SP-83, MSS SP-95, and MSS SP-97. Fittings differing from these ASME and MSS standards shall be furnished...
1.1 This test method provides a comparative oxidation mass loss of manufactured carbon and graphite materials in air. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address...
1.1 This specification covers wrought-carbon steel butt-welding seamless or welded fittings specially processed to ensure better notch toughness than that to be expected in fittings manufactured to the requirements of Specification A234/A234M. 1.1.1 Included are elbows, caps, tees, reducers,...
1.1 This specification covers coppered carbon steel wire supplied in coils for general use. It may be produced hard drawn, annealed in process, or annealed at finish size. The coating is very thin and is not designed for protection against corrosion. 1.2 The values stated in inch-pound units...
1.1 This specification covers a group of common requirements that, unless otherwise specified in the individual product specification, shall apply to steel forgings under any of the following specifications issued by ASTM: ASTM Designation Title A266/A266M Carbon Steel Forgings for Pressure...
This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures. The material for fittings shall consist of killed...
3.1 Committee D36 has concluded that typical carbon black characterization methods based on structure level and surface area measurements do not seem to correlate to in-rubber performance in an equal manner for Recovered Carbon Black products. Therefore, the committee does not...
1.1 This test method covers the determination of the mass strength of pelleted carbon black. It is designed to determine the force required to pack a cylindrical column of pelleted carbon black. The results of this test are believed to relate to the ability of the carbon black...
4.1 The oil absorption number of a carbon black is related to the processing and vulcanizate properties of rubber compounds containing the carbon black. 4.2 The difference between the regular oil absorption number and the oil absorption number of compressed sample is some measure of...
1.1 These test methods cover procedures for the chemical and mass spectrometric analysis of nuclear-grade gadolinium oxide powders to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Carbon by Direct Combustion-Thermal...
1.1 This test method specifies procedures for the metallographic determination of apparent porosity in cemented carbides. Note 1: The term "apparent porosity" is construed to mean all microstructures observed on a properly prepared, unetched surface, including structures resulting from uncombined...
5.1 These test methods are used to estimate the amount of volatile materials present in a material. 5.2 These test methods are useful for design purposes, service evaluation, regulatory statutes, manufacturing control, quality control, specification acceptance, development, and research. 5.3 The...