loading
ASTM 51818-26 - Standard Practice for Dosimetry in an Electron Beam Facility for Radiation Processing at Energies Between 80 and 300 keV
June 1, 2026 - ASTM International

1.1 This practice covers dosimetric procedures to be followed in installation qualification, operational qualification, performance qualification (IQ, OQ, PQ), and routine processing at electron beam facilities to ensure that the product has been treated with an acceptable range of absorbed doses....

MIL-C-37106 - CASE, MEDICAL LABORATORY EQUIPMENT SET
NPFC
A description is not available for this item.
ASTM F3263-17(2025) - Standard Guide for Packaging Test Method Validation
October 1, 2025 - ASTM International

4.1 Addressing consensus standards with inter-laboratory studies (ILS) and methods specific to an organization. Test methods need to be validated in many cases, in order to be able to rely on the results. This has to be done at the organization performing the tests but is also performed in...

ASTM F3661-24 - Standard Guide for Assessing Fit Accommodation of Exoskeletons for Manufacturers and Designers
November 15, 2024 - ASTM International

4.1 Improperly fitted exoskeletons may cause discomfort, distraction, stress, disuse, accidents, and therefore, may cause unacceptable risk of injury or damage to the health of users (1).5 An improperly fitted exoskeleton can also cause a loss of cognitive fit and task failure. According to Ref...

ASTM F2819-24 - Standard Test Methods for Measurement of Straightness of Bar, Rod, Tubing, and Wire to be Used for Medical Devices
August 15, 2024 - ASTM International

5.1 Significance-With the birth of minimally invasive surgery in the 1960s, there has been a requirement for guide wires. The guide wires serve as the access line by which procedures like balloon angioplasty and stent placement are conducted. A guide wire typically consists of a mandrel, coil, and...

ASTM F1819-24 - Standard Test Method for Resistance of Materials Used in Protective Clothing to Penetration by Synthetic Blood Using a Mechanical Pressure Technique
November 1, 2024 - ASTM International

5.1 This test method was modeled after a procedure commonly known as the Elbow Lean Test.8 The Elbow Lean Test involves the application of synthetic blood to an ink pad, placement of sample fabric over the blood-soaked pad, placement of a blotter over the sample fabric, and applying elbow or...

ASTM F3604-23 - Standard Practice for Validating the Additive Manufacturing (AM) Production Process for Medical Devices Produced Using Laser Powder Bed Fusion
October 15, 2023 - ASTM International

1.1 This practice provides an overview of how to perform process validation for medical devices manufactured using PBF/LB/M. The topics that will be covered include machine qualifications, software used in the manufacturing process, the importance of design specification and verification on...

ASTM E2186-02a(2023) - Standard Guide for Determining DNA Single-Strand Damage in Eukaryotic Cells Using the Comet Assay
December 1, 2023 - ASTM International

1.1 This guide covers the recommended criteria for performing a single-cell gel electrophoresis assay (SCG) or Comet assay for the measurement of DNA single-strand breaks in eukaryotic cells. The Comet assay is a very sensitive method for detecting strand breaks in the DNA of individual cells. The...

ASTM D5791-23 - Standard Guide for Using Probability Sampling Methods in Studies of Indoor Air Quality in Buildings
September 1, 2023 - ASTM International

1.1 This guide covers criteria for determining when probability sampling methods should be used to select locations for placement of environmental monitoring equipment in a building or to select a sample of building occupants for questionnaire administration for a study of indoor air quality...

JIS MEDICAL DEVICES I - JIS Medical Devices I Handbook
January 1, 2015 - JSA
A description is not available for this item.
JIS MEDICAL DEVICES III - JIS Medical Devices III Handbook
January 1, 2015 - JSA
A description is not available for this item.
JIS MEDICAL DEVICES II - JIS Medical Devices II Handbook
January 1, 2015 - JSA
A description is not available for this item.
JIS MEDICAL DEVICES IV - JIS Medical Devices IV Handbook
January 1, 2015 - JSA
A description is not available for this item.
ASTM D8150-22 - Standard Test Method for Determination of Organic Chloride Content in Crude Oil by Distillation Followed by Detection Using Combustion Ion Chromatography
October 1, 2022 - ASTM International

5.1 Organic chlorides do not occur naturally in crude oil. When present, they result from contamination in some manner, such as disposal of chlorinated solvent used in many dewaxing pipeline or other equipment operations. 5.1.1 Uncontaminated crude oil will contain no detectable organic...

ASTM E2124-20 - Standard Specification for Equipment and Supplies in Sexual Violence Investigations
September 1, 2020 - ASTM International

This practice describes the basic instruments, equipments, and supplies used for the medical-legal examination of the victims and/or suspects in sexual assault investigations. Outlined here are the considerations for choosing a variation or optional equipment to be used, in...

ASTM D2878-21 - Standard Test Method for Estimating Apparent Vapor Pressures and Molecular Weights of Lubricating Oils
December 1, 2021 - ASTM International

1.1 This test method covers a calculation procedure for converting data obtained by Test Method D972 to apparent vapor pressures and molecular weights. It has been demonstrated to be applicable to petroleum-based and synthetic ester lubricating oils,2 at temperatures of 395 K to 535 K (250 °F to...

ASTM E3336-22 - Standard Test Method for Physical Integrity Testing of Single-Use Systems
February 1, 2022 - ASTM International

1.1 The test methods described in this standard are applicable for single-use manufacturing equipment, further called Single-use Systems (SUSs), used for (bio)pharmaceutical products. 1.2 The test methods described in this standard are not intended to be used on single-use technology for...

Advertisement