loading
API INSPECTION REFINERY 1 - Guide for Inspection of Refinery Equipment Chapter I - Introduction
January 1, 1961 - API

PREFACE This chapter is one of a series which make up the manual, Guide for Inspection of Refinery Equipment. It is based on the accumulated knowledge and experience of engineers of the petroleum industry. All users are invited to submit suggested revisions to the director of the Division of...

SSPC INSPECTION OF COATIN - THE INSPECTION OF COATINGS AND LININGS
SSPC
A description is not available for this item.
ASTM D7400/D7400M-26 - Standard Test Methods for Downhole Seismic Testing
February 15, 2026 - ASTM International

5.1 The seismic downhole method provides a designer with information pertinent to the seismic wave velocities of the materials in question (1). The P-wave and S-wave velocities are directly related to the important geotechnical elastic constants of Poisson's ratio, shear modulus, bulk modulus, and...

ASTM D5875/D5875M-18(2025) - Standard Guide for Use of Cable-Tool Drilling and Sampling Methods for Geoenvironmental Exploration and Installation of Subsurface Water Quality Monitoring Devices
July 1, 2025 - ASTM International

4.1 Cable-tool rigs (also referred to as churn rigs, water-well drilling rigs, spudders, or percussion rigs) are used in the oil fields and in the water-well industry. The Chinese developed the percussion method some 4,000 years ago. 4.2 Cable-tool drilling and sampling methods may be used in...

ASTM D6151-25 - Standard Practice for Using Hollow-Stem Augers for Geotechnical Exploration and Soil Sampling
July 1, 2025 - ASTM International

4.1 Hollow-stem augers are frequently used for geotechnical exploration. One reason they are used is that the method is considered a "dry" drilling method where drill fluids are not needed to advance the borehole in unstable formations. Often, hollow-stem augers are used with other sampling...

ASTM D5781/D5781M-18(2025) - Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water Quality Monitoring Devices
February 15, 2025 - ASTM International

4.1 Dual-wall reverse-circulation drilling can be used in support of geoenvironmental exploration and for installation of subsurface water quality monitoring devices in unconsolidated and consolidated sediment or bedrock. Dual-wall reverse-circulation drilling methods allows for the collection of...

ASTM D5784/D5784M-18(2025) - Standard Guide for Use of Hollow-Stem Augers for Geoenvironmental Exploration and the Installation of Subsurface Water Quality Monitoring Devices
February 15, 2025 - ASTM International

4.1 Hollow-stem auger drilling may be used in support of geoenvironmental exploration (Practice D3550/D3550M, Test Method D4428/D4428M) and for installation of subsurface water quality monitoring devices in unconsolidated sediment. Hollow-stem auger drilling may be selected over other methods based...

NACE SP21475 - Prioritization of External Corrosion on Piping Within Metallic Casings using In-Line Inspection Data
December 2, 2020 - NACE

ABSTRACT This NACE International standard provides the most current technology and industry practices for prioritization of cased piping using In-Line Inspection (ILI) data. Metallic casings are used to install and protect the carrier pipe at pipeline crossings such as those at road...

ASTM D6282/D6282M-25 - Standard Guide for Direct Push Soil Sampling for Environmental Site Characterizations
March 1, 2025 - ASTM International

5.1 Direct Push Soil Sampling is used extensively in environmental site characterization of soils below ground surface and can also be used for subsurface geotechnical site characterization (3, 7-13). Limited early studies have been done using Direct Push Soil Sampling for environmental...

ASTM D4428/D4428M-25 - Standard Test Methods for Crosshole Seismic Testing of Soil and Rock
January 15, 2025 - ASTM International

1.1 These test methods are limited to the determination of the low strain (<10-4?%) velocity of two types of horizontally travelling seismic waves in soil materials; primary compression (P-wave) and secondary shear (S-wave) waves. The standard assumes that the method used to analyze the data...

ASTM D6914/D6914M-16(2024) - Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices
March 15, 2024 - ASTM International

5.1 Sonic drilling is a rapid, primarily dry drilling method (see 5.2), used both in geotechnical applications to avoid hydraulic fracturing, and in environmental site exploration. Geotechnical applications include exploration for tunnels, underground excavations, and installation of...

API SPEC 5B - Threading, Gauging, and Inspection of Casing, Tubing, and Line Pipe Threads
December 1, 2017 - API

Coverage-Threading and Gauging This specification covers dimensions, tolerances, and marking requirements for API threads and the gauges that control the acceptance criteria for the threads. Thread element gauges, instruments, and requirements for the inspection of threads for line pipe,...

NACE 35100 - In-Line Inspection of Pipelines
January 14, 2022 - NACE

This NACE technical committee report was prepared by Task Group (TG) 039, (formerly T-10E-6) on In-Line Nondestructive Inspection of Pipelines, which is administered by Specific Technology Group (STG) 35, Pipelines, Tanks, and Well Casings. This report is issued by NACE International...

ASTM C1208/C1208M-18(2022) - Standard Specification for Vitrified Clay Pipe and Joints for Use in Microtunneling, Sliplining, Pipe Bursting, and Tunnels
November 1, 2022 - ASTM International

This specification establishes the criteria for the manufacture, quality assurance testing, inspection, installation, field acceptance testing, inspection, installation, field acceptance testing, and product marking of vitrified clay pipe to be used in microtunneling, pilot tube...

API RP 5B1 - Gauging and Inspection of Casing, Tubing, and Line Pipe Threads
October 1, 1999 - API

Information contained in this recommended practice is intended for use of pipe manufacturer inspectors, quality control personnel, field inspectors, threading unit operators, and users and purchasers of oil country tubular goods and line pipe. This publication was prepared under the auspices of the...

ISO 11960 - Petroleum and natural gas industries — Steel pipes for use as casing or tubing for wells
March 1, 2020 - ISO

This document specifies the technical delivery conditions for steel pipes (casing, tubing and pup joints), coupling stock, coupling material and accessory material. By agreement between the purchaser and manufacturer, this document can also be applied to other plain-end pipe sizes and wall...

IEEE SOFTWARE INSPECTION - SOFTWARE INSPECTION: AN INDUSTRY BEST PRACTICE
IEEE
A description is not available for this item.
Advertisement