1.1 This specification covers the materials and testing of shielded hubless couplings to join hubless cast iron soil pipe and fittings. 1.2 Several different types of hubless couplings are available for use in hubless cast iron sanitary and storm drain, waste, and vent...
This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an...
This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an...
1.1 This specification covers the evaluation of the performance of heavy-duty shielded couplings to join hubless cast iron soil pipe and fittings. 1.2 Couplings covered by this standard shall have nominal dimensions as found in Table 1 and Fig. 1. 1.3 The values stated in inch-pound...
Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. This material specification covers castings made of nodular iron, also known as spheroidal or...
This specification covers preformed rubber gaskets used to seal joints in cast iron soil pipe and fittings. Gaskets shall be made of a properly vulcanized virgin rubber as the sole elastomer with no scrap or reclaim. Gaskets shall conform to the required physical properties such as...
This specification covers piston rings fabricated from cast iron.
Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose/Material Description. Gray cast iron. Symbols. Not applicable. Applicability. This...
1.1 This specification covers cast iron soil closet flanges for use in gravity flow plumbing drain, waste, and vent sanitary applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification,...
Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. This specification describes cast iron flywheel porosity inspection...
This Standard for cast iron threaded drainage fittings covers (a) sizes and method of designating openings in reducing fittings (b) marking (c) material (d) dimensions and tolerances (e) threading (f) ribs (g) coatings (h) face bevel
Introduction Note: Nothing in this standard supercedes applicable laws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. Purpose. This specification defines the requirements and test conditions for finish machined...
This material specification covers castings made of high temperature resistant iron as used in automotive and allied industries, including the mechanical properties from separately cast Y-block test samples and compositional requirements in the product castings. Any specific...
1.1 These test methods cover the chemical analysis of pig iron, gray cast iron (including alloy and austenitic), white cast iron, malleable cast iron, and ductile (nodular) iron having chemical compositions within the following limits: Element...
This material specification applies to those grades of gray iron castings intended for a wide range of automotive applications. This standard describes the material properties, not specific casting properties, based on data obtained from separately cast test samples. Any specific...
This specification covers the materials and testing of cast iron couplings for joining hubless cast iron soil pipe and fittings for sizes 1½ to 10 in. It is the purpose of this specification to furnish information as to the characteristics of a particular sleeve type...
1.1 This specification covers the materials and testing of cast iron couplings for joining hubless cast iron soil pipe and fittings for sizes 11/2 to 10 in. 1.2 It is the purpose of this specification to furnish information as to the characteristics of a particular...
1.1 This test method covers the analysis of cast iron by spark atomic emission spectrometry for the following elements in the ranges shown (Note 1): Ranges, % Elements Applicable Range, % Quantitative Range, %A Carbon 1.9 to 3.8 1.90? to 3.8 Chromium 0 to 2.0 0.025 to 2.0 Copper 0 to...
Narrow Your Results