1.1 The resistance to breakage of formed catalysts, catalyst carriers, or catalyst pieces is determined by dropping a quantity of sample through a 25?ft length of 1?in. internal diameter pipe onto a steel plate. 1.2 This standard does not purport to address all of the safety...
1.1 This test method covers the determination of nitrogen adsorption and desorption isotherms of catalysts and catalyst carriers at the boiling point of liquid nitrogen. A static volumetric measuring system is used to obtain sufficient equilibrium adsorption points on each branch of...
5.1 Advanced ceramic powders and porous ceramic bodies often have a very fine particulate morphology and structure that are marked by high surface-to-volume (S-V) ratios. These ceramics with high S-V ratios commonly exhibit enhanced chemical reactivity and lower sintering temperatures. Results of...
1.1 This test method covers determining the activity of equilibrium or laboratory-deactivat
5.1 Zeolite composition with reference to silica and alumina is an important indicator of zeolite performance and is a valuable tool for assessing parameters in various industrial zeolite based catalyst processes. 5.2 This guide will be useful to zeolite manufacturers and end users...
1.1 This test method covers the determination of the particle size distribution of catalyst, catalyst carrier, and catalytic raw material particles and is one of several found valuable for the measurement of particle size. The range of average particle sizes investigated was from 1 to...
1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs). These...
5.1 The evaporation loss is of particular importance in engine lubrication. Where high temperatures occur, portions of an oil can evaporate. 5.2 Evaporation may contribute to oil consumption in an engine and can lead to a change in the properties of an oil. 5.3 Many engine manufacturers specify a...
5.1 This test method can be used to determine total sulfur levels in process feeds and finished products that fall within the scope of this test method. 5.2 Low levels of sulfur in process feed stocks can poison expensive catalysts used in petroleum refining processes. This test method can...
5.1 This test method is used to determine the approximate chloride content of crude oils, a knowledge of which is important in deciding whether or not the crude oil needs desalting. The efficiency of the process desalter can also be evaluated. 5.2 Excessive chloride left in the crude oil frequently...
1.1 This test method covers the determination of surface areas of catalyst and catalyst carriers that have Type II or IV nitrogen adsorption isotherms, and at least 1 m2/g of area. A volumetric measuring system is used to obtain at least four data points which fit on the linear BET2...
5.1 This test method usually requires several minutes per sample. Other test methods which can be used for the determination of phosphorus in lubricating oils include WDXRF Test Method D4927 and ICPAES Test Methods D4951 and D5185. However, this test method provides more precise results than Test...
1.1 This test method covers the oxidation stability of lubricants by thin-film oxygen uptake (TFOUT) Catalyst B. This test method evaluates the oxidation stability of petroleum products, and it was originally developed as a screening test to indicate whether a given re-refined base stock...
5.1 The data from this guide seldom, if ever, directly simulate thermal and pressure events in the processing, storage, and shipping of chemicals (see Appendix X2.1.1 for more detail). However, the data obtained from this guide may be used, with suitable precautions, to predict the thermal and...
5.1 This test method is intended to determine the volume distribution of pores in catalysts and catalyst carriers with respect to the apparent diameter of the entrances to the pores. In general, both the size and volume of pores in a catalyst affect its performance. Thus, the...
4.1 The ash content of a carbon black is the amount of non-carbon components present after combustion. Primary contributants to ash are the manufacturing process water and the catalyst in the feedstock.
1.1 This specification covers three types of nitrogen used as an electrical insulating material in electrical equipment: 1.1.1 Type I, obtained from the air by liquefaction processes and dried, 1.1.2 Type II, obtained from the air by liquefaction processes, deoxidized with hydrogen over a platinum...
4.1 Organic peroxides are widely used as chemical intermediates, catalysts, and initiators. These test methods provide procedures for assaying organic peroxides to determine if they are suitable for their intended use.
1.1 This test method covers the determination of gamma alumina and related transition aluminas in catalysts and catalyst carriers containing silica and alumina by X-ray powder diffraction, using the diffracted intensity of the peak occurring at about 67 °2? when copper Ka radiation is...
5.1 The determination of oxygenates is important in the manufacture of ethene, propene, 1-3 butadiene, C4 hydrocarbons, and C5 hydrocarbons. Alcohols, ethers, aldehydes, and ketones are trace impurities in these hydrocarbons. Oxygenates decrease catalyst activity in downstream polymerization...
Narrow Your Results