loading
ASTM D8353-26 - Standard Guide for Determination of Individual Particle Strength of Low Surface Area Catalysts and Catalyst Carriers by Drop Test onto a Steel Plate
April 1, 2026 - ASTM International

1.1 The resistance to breakage of formed catalysts, catalyst carriers, or catalyst pieces is determined by dropping a quantity of sample through a 25?ft length of 1?in. internal diameter pipe onto a steel plate. 1.2 This standard does not purport to address all of the safety...

ASTM D4222-26 - Standard Test Method for Determination of Nitrogen Adsorption and Desorption Isotherms of Catalysts and Catalyst Carriers by Static Volumetric Measurements
April 1, 2026 - ASTM International

1.1 This test method covers the determination of nitrogen adsorption and desorption isotherms of catalysts and catalyst carriers at the boiling point of liquid nitrogen. A static volumetric measuring system is used to obtain sufficient equilibrium adsorption points on each branch of...

ASTM C1274-12(2026) - Standard Test Method for Advanced Ceramic Specific Surface Area by Physical Adsorption
July 15, 2026 - ASTM International

5.1 Advanced ceramic powders and porous ceramic bodies often have a very fine particulate morphology and structure that are marked by high surface-to-volume (S-V) ratios. These ceramics with high S-V ratios commonly exhibit enhanced chemical reactivity and lower sintering temperatures. Results of...

ASTM D3907/D3907M-26 - Standard Test Method for Testing Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test
June 1, 2026 - ASTM International

1.1 This test method covers determining the activity of equilibrium or laboratory-deactivated fluid catalytic cracking (FCC) catalysts, or both. This is evaluated on the basis of mass percent conversion of gas oil feed in a microactivity unit. The selectivity of FCC catalysts can be...

ASTM D8671-26 - Standard Guide for Determination of Silica and Alumina Molar Ratio in Zeolites by Inductively Coupled Plasma Optical Emission Spectroscopy
June 1, 2026 - ASTM International

5.1 Zeolite composition with reference to silica and alumina is an important indicator of zeolite performance and is a valuable tool for assessing parameters in various industrial zeolite based catalyst processes. 5.2 This guide will be useful to zeolite manufacturers and end users...

ASTM D4464-26 - Standard Test Method for Particle Size Distribution of Catalytic Materials by Laser Light Scattering
April 1, 2026 - ASTM International

1.1 This test method covers the determination of the particle size distribution of catalyst, catalyst carrier, and catalytic raw material particles and is one of several found valuable for the measurement of particle size. The range of average particle sizes investigated was from 1 to...

ASTM D7859-26 - Standard Practice for Spraying, Sampling, Packaging, and Test Specimen Preparation of Spray Polyurethane Foam (SPF) Insulation for Testing of Emissions Using Environmental Chambers
April 1, 2026 - ASTM International

1.1 This practice describes standardized procedures for the preparation, spraying, packaging, and shipping of fresh spray polyurethane foam (SPF) insulation product samples to be tested for their emissions of volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs). These...

ASTM D5800-21(2026) - Standard Test Method for Evaporation Loss of Lubricating Oils by the Noack Method
April 1, 2026 - ASTM International

5.1 The evaporation loss is of particular importance in engine lubrication. Where high temperatures occur, portions of an oil can evaporate. 5.2 Evaporation may contribute to oil consumption in an engine and can lead to a change in the properties of an oil. 5.3 Many engine manufacturers specify a...

ASTM D7041-26 - Standard Test Method for Determination of Total Sulfur in Liquid Hydrocarbons and Hydrocarbon-Oxygenate Blends by Gas Chromatography with Flame Photometric Detection
March 1, 2026 - ASTM International

5.1 This test method can be used to determine total sulfur levels in process feeds and finished products that fall within the scope of this test method. 5.2 Low levels of sulfur in process feed stocks can poison expensive catalysts used in petroleum refining processes. This test method can...

ASTM D3230-26 - Standard Test Method for Salts in Crude Oil (Electrometric Method)
March 1, 2026 - ASTM International

5.1 This test method is used to determine the approximate chloride content of crude oils, a knowledge of which is important in deciding whether or not the crude oil needs desalting. The efficiency of the process desalter can also be evaluated. 5.2 Excessive chloride left in the crude oil frequently...

ASTM D3663-25 - Standard Test Method for Surface Area of Catalysts and Catalyst Carriers
September 1, 2025 - ASTM International

1.1 This test method covers the determination of surface areas of catalyst and catalyst carriers that have Type II or IV nitrogen adsorption isotherms, and at least 1 m2/g of area. A volumetric measuring system is used to obtain at least four data points which fit on the linear BET2...

ASTM D7040-26 - Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
March 1, 2026 - ASTM International

5.1 This test method usually requires several minutes per sample. Other test methods which can be used for the determination of phosphorus in lubricating oils include WDXRF Test Method D4927 and ICPAES Test Methods D4951 and D5185. However, this test method provides more precise results than Test...

ASTM D7098-25 - Standard Test Method for Oxidation Stability of Lubricants by Thin-Film Oxygen Uptake (TFOUT) Catalyst B
October 1, 2025 - ASTM International

1.1 This test method covers the oxidation stability of lubricants by thin-film oxygen uptake (TFOUT) Catalyst B. This test method evaluates the oxidation stability of petroleum products, and it was originally developed as a screening test to indicate whether a given re-refined base stock...

ASTM E1981-26 - Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry
February 1, 2026 - ASTM International

5.1 The data from this guide seldom, if ever, directly simulate thermal and pressure events in the processing, storage, and shipping of chemicals (see Appendix X2.1.1 for more detail). However, the data obtained from this guide may be used, with suitable precautions, to predict the thermal and...

ASTM D4284-25 - Standard Test Method for Determining Pore Volume Distribution of Catalysts and Catalyst Carriers by Mercury Intrusion Porosimetry
September 1, 2025 - ASTM International

5.1 This test method is intended to determine the volume distribution of pores in catalysts and catalyst carriers with respect to the apparent diameter of the entrances to the pores. In general, both the size and volume of pores in a catalyst affect its performance. Thus, the...

ASTM D1506-25 - Standard Test Methods for Carbon Black—Ash Content
December 15, 2025 - ASTM International

4.1 The ash content of a carbon black is the amount of non-carbon components present after combustion. Primary contributants to ash are the manufacturing process water and the catalyst in the feedstock.

ASTM D1933-03(2026) - Standard Specification for Nitrogen Gas as an Electrical Insulating Material
January 1, 2026 - ASTM International

1.1 This specification covers three types of nitrogen used as an electrical insulating material in electrical equipment: 1.1.1 Type I, obtained from the air by liquefaction processes and dried, 1.1.2 Type II, obtained from the air by liquefaction processes, deoxidized with hydrogen over a platinum...

ASTM E298-25a - Standard Test Methods for Assay of Organic Peroxides
December 1, 2025 - ASTM International

4.1 Organic peroxides are widely used as chemical intermediates, catalysts, and initiators. These test methods provide procedures for assaying organic peroxides to determine if they are suitable for their intended use.

ASTM D4926-25 - Standard Test Method for Gamma Alumina Content in Catalysts and Catalyst Carriers Containing Silica and Alumina by X-ray Powder Diffraction
September 1, 2025 - ASTM International

1.1 This test method covers the determination of gamma alumina and related transition aluminas in catalysts and catalyst carriers containing silica and alumina by X-ray powder diffraction, using the diffracted intensity of the peak occurring at about 67 °2? when copper Ka radiation is...

ASTM D7423-25 - Standard Test Method for Determination of Oxygenates in C2, C3, C4, and C5 Hydrocarbon Matrices by Gas Chromatography and Flame Ionization Detection
November 1, 2025 - ASTM International

5.1 The determination of oxygenates is important in the manufacture of ethene, propene, 1-3 butadiene, C4 hydrocarbons, and C5 hydrocarbons. Alcohols, ethers, aldehydes, and ketones are trace impurities in these hydrocarbons. Oxygenates decrease catalyst activity in downstream polymerization...

Advertisement