4.1 Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. 4.2 This...
Digests 164 and 165 were published in 1970s. They covered performance, specification and general design issues for clay bricks and appropriate mortars used in a wide range of building elements. Since then markets and products, Codes and Standards have changed and will change further....
A review of the production, performance and economic advantages of perforated clay bricks over wholly solid units.
This Standard covers hollow building and facing brick made from clay, shale, fireclay, or mixtures thereof and burned for use in brick masonry. This Standard excludes ceramic or other glazed brick. Brick to be treated with water-repellent materials must qualify...
Digests 164 and 165 were published in 1970s. They covered performance, specification and general design issues for clay bricks and appropriate mortars used in a wide range of building elements. Since then markets and products, Codes and Standards have changed and will change further....
Requirements for dimensions, compressive strength, water absorption, soluble salt content, efflorescence and sampling for bricks manufactured from clay for use in walling. Also gives methods of classification and guidance on appearance. Sizes and tolerances apply only to the 225 mm x...
Specifies the requirements for clay bricks with modular dimensions.
Digests 164 and 165 were published in 1970s. They covered performance, specification and general design issues for clay bricks and appropriate mortars used in a wide range of building elements. Since then markets and products, Codes and Standards have changed and will change further....
4.1 Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. 4.2 This...
This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the...
Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. This practice...
1.1 This practice is intended to provide accepted installation procedures for thin brick units in adhered veneer systems in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of clay and...
This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing...
This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or altering...
1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or...
1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or...
1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and...
This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing...
This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the...
Narrow Your Results