loading
AFS CLAY - AFS Clay
AFS
A description is not available for this item.
ASTM D5703-95(2022)e1 - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
January 1, 2022 - ASTM International

4.1 Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. 4.2 This...

Clay bricks and clay brick masonry
January 1, 1998 - BRE

Digests 164 and 165 were published in 1970s. They covered performance, specification and general design issues for clay bricks and appropriate mortars used in a wide range of building elements. Since then markets and products, Codes and Standards have changed and will change further....

Perforated clay bricks
January 1, 1983 - BRE

A review of the production, performance and economic advantages of perforated clay bricks over wholly solid units.

CSA A82.8 - Hollow Clay Brick
October 1, 1978 - CSA

This Standard covers hollow building and facing brick made from clay, shale, fireclay, or mixtures thereof and burned for use in brick masonry. This Standard excludes ceramic or other glazed brick. Brick to be treated with water-repellent materials must qualify...

Clay bricks and clay brick masonry Part 1
November 1, 1999 - BRE

Digests 164 and 165 were published in 1970s. They covered performance, specification and general design issues for clay bricks and appropriate mortars used in a wide range of building elements. Since then markets and products, Codes and Standards have changed and will change further....

BS 3921 - Clay Bricks
November 29, 1985 - BSI

Requirements for dimensions, compressive strength, water absorption, soluble salt content, efflorescence and sampling for bricks manufactured from clay for use in walling. Also gives methods of classification and guidance on appearance. Sizes and tolerances apply only to the 225 mm x...

BS DD 34 - Clay bricks with modular dimensions
May 20, 1974 - BSI

Specifies the requirements for clay bricks with modular dimensions.

Clay bricks and clay brick masonry Part 2
November 1, 1999 - BRE

Digests 164 and 165 were published in 1970s. They covered performance, specification and general design issues for clay bricks and appropriate mortars used in a wide range of building elements. Since then markets and products, Codes and Standards have changed and will change further....

ASTM D5703-95(2013) - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
June 1, 2013 - ASTM International

4.1 Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. 4.2 This...

ASTM C1088-26 - Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
June 1, 2026 - ASTM International

This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the...

ASTM D5703-95(2007) - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
July 1, 2007 - ASTM International

Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. This practice...

ASTM C1935-26 - Standard Practice for Installation Methods for Adhered Veneer Systems Using Thin Brick Units Made from Clay or Shale
June 1, 2026 - ASTM International

1.1 This practice is intended to provide accepted installation procedures for thin brick units in adhered veneer systems in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of clay and...

ASTM C216-26a - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
June 1, 2026 - ASTM International

This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing...

ASTM D5703 - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
April 15, 1995 - ASTM

This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or altering...

ASTM D5703-95 - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
April 15, 1995 - ASTM International

1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or...

ASTM D5703-95(2001) - Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry
April 15, 1995 - ASTM International

1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or...

ASTM C67/C67M-25 - Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile
August 1, 2025 - ASTM International

1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and...

ASTM C216-26 - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
February 1, 2026 - ASTM International

This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. Bricks shall be classified according to their resistance to damage by freezing when saturated at a moisture content: Grade SW and Grade MW. The facing...

ASTM C1088-24 - Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
December 1, 2024 - ASTM International

This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. The brick units shall be available in both Grades Interior and Exterior of the...

Advertisement