loading
ASTM C1838-16(2026) - Standard Practice for Cleaning for 1S and 2S Bottles
June 1, 2026 - ASTM International

1.1 This practice provides a description of the different ways to clean uranium hexafluoride (UF6) bottles. 1.2 This practice describes two kinds of sample bottles: 1S and 2S bottles. 1.3 Units-The values stated in SI units are to be regarded as the standard. No other units of measurement...

ASTM D2200-26 - Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces
June 1, 2026 - ASTM International

4.1 The appearance of the various degrees of dry and wet abrasive blast cleaning, hand and power tool cleaning, and water jetting are influenced by the initial rust grades of the steel being cleaned and/or the type and condition of the coating on the existing steel. The...

ASTM D4677-87(2026) - Standard Classification for Rubber Compounding Materials—Titanium Dioxide
July 1, 2026 - ASTM International

3.1 Titanium dioxide is used in rubber compounding as a colorant to impart whiteness to any desired end product. It is used in sidewalls of automobile tires. 3.2 It is chemically inert and slightly basic with a pH of 7.0 to 8.0. The free-chalking, weathering properties of anatase titanium-dioxide...

ASTM F91-06(2026) - Standard Practice for Testing for Leaks in the Filters Associated With Laminar Flow Clean Rooms and Clean Work Stations by Use of a Condensation Nuclei Detector
July 1, 2026 - ASTM International

This practice covers the testing of the integrity of high-efficiency particulate air (HEPA) filters installed in laminar flow clean rooms of the ceiling to floor or wall to wall type, and laminar flow clean work stations using condensation nuclei detector. The recommended practice may...

ASTM D8430-26 - Standard Test Method for Determination of Ammonia Nitrogen by Semi-Automated Gas Diffusion Colorimetry
July 1, 2026 - ASTM International

5.1 This test method is used for measuring ammonia and ammonium ion in water samples and soil or plant extracts. 5.2 Ammonia compounds are widely distributed in the environment and may be applied as fertilizer, used as cleaning compounds, or used in water treatment. 5.3 Ammonia nitrogen...

ASTM D8271-26 - Standard Test Method for Direct Measurement of Surface Profile of Prepared Concrete
June 1, 2026 - ASTM International

4.1 Proper bonding of coatings and linings to concrete surfaces requires proper cleaning and frequently requires the concrete to be roughened to increase the surface area. The roughness, also known as surface profile, can be imparted into concrete by abrasive blast cleaning, acid...

ASTM E2905/E2905M-26 - Standard Practice for Examination of Mill and Kiln Girth Gear Teeth—Electromagnetic Methods
July 1, 2026 - ASTM International

Note 1: Throughout the practice, "gear" means gear or pinion unless the gear is specifically identified. 1.1 This practice describes a two-part procedure for examination of gear teeth on mill and kiln gear drives and pinions using eddy current array (ECA) methods. The first part of this practice...

ASTM B614-26 - Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces
April 1, 2026 - ASTM International

1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants...

ASTM D4970/D4970M-22(2026) - Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Martindale Tester
July 1, 2026 - ASTM International

1.1 This test method covers the determination of the resistance to the formation of pills and other related surface changes on textile fabrics using the Martindale tester. Note 1: For other methods, if testing the pilling resistance of textiles, refer to Test Methods D3511/D3511M, D3512/D3512M, and...

ASTM D8457-26 - Standard Practice for Cleaning Glass and Plastic Labware Used in Metal and Metalloid Analyses
March 1, 2026 - ASTM International

1.1 This practice uses dilute nitric acid to clean glass and plastic labware used in laboratories preparing and analyzing samples for metal and metalloid content. 1.2 Practice D5245 describes cleaning labware used in microbiological analyses. Practice D8589 describes cleaning...

ASTM F21-20(2026) - Standard Test Method for Hydrophobic Surface Films by the Atomizer Test
July 1, 2026 - ASTM International

5.1 The atomizer test as described in this test method is rapid, nondestructive, and may be used for control and evaluation of processes for the removal of hydrophobic contaminants. The test may also be used for the detection and control of hydrophobic contaminants in processing environments. For...

ASTM D5367-26 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Additives Used to Prevent Flash Rusting of Steel When Vapor, Water, or Water/Abrasive Blasted
June 1, 2026 - ASTM International

1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC), and...

ASTM D6279-26 - Standard Test Method for Rub Abrasion Mar Resistance of High Gloss Coatings
June 1, 2026 - ASTM International

5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning and exposure) during manufacture and service that can mar their surface. The ability of high gloss coatings to maintain their...

ASTM B177/B177M-11(2026) - Standard Guide for Engineering Chromium Electroplating
July 1, 2026 - ASTM International

This guide provides information on the deposition of engineering chromium by electroplating. This is sometimes called "functional" or "hard" chromium and is usually applied directly to the basis metal and is usually thicker than decorative deposits. This guide is not intended as a standardized...

ASTM B841-26 - Standard Specification for Electrodeposited Coatings of Zinc Nickel Alloy Deposits
July 1, 2026 - ASTM International

This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings, Type B shall be with...

ASTM F2388-21(2026) - Standard Consumer Safety Specification for Baby Changing Products for Domestic Use
July 1, 2026 - ASTM International

This consumer safety specification covers performance requirements, test methods, and labeling requirements to promote the safe use of baby changing tables and other changing surfaces such as contoured changing pads and add-on changing units that are sold separately for use on furniture products...

ASTM F1449-20(2026) - Standard Guide for Industrial Laundering Care and Maintenance of Flame Resistant or Arc Rated Clothing
May 1, 2026 - ASTM International

1.1 This guide provides recommendations for the care and maintenance of clothing that is flame resistant or arc rated. 1.2 These recommendations address the industrial laundering process. Industrial laundering is an effective cleaning process for flame resistant or arc rated clothing; follow...

ASTM F2757-20(2026) - Standard Guide for Home Laundering Care and Maintenance of Flame Resistant or Arc Rated Clothing
May 1, 2026 - ASTM International

1.1 This guide provides recommendations for home laundering of clothing that is flame resistant or arc rated. These recommendations address the home laundering process. Home laundering is an effective cleaning process for flame resistant or arc rated garments; follow all label care...

ASTM D6037-26 - Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
June 1, 2026 - ASTM International

5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning, and exposure) that can mar their surface. The ability of these coatings to maintain their appearance is an important product...

ASTM C430-26 - Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the fineness of hydraulic cement by means of the 45-μm (No. 325) sieve. 1.1.1 This test method may be used for the determination of the fineness of other materials. However, certain requirements, such as calibration procedures, cleaning of...

Advertisement