1.1 This practice provides a description of the different ways to clean uranium hexafluoride (UF6) bottles. 1.2 This practice describes two kinds of sample bottles: 1S and 2S bottles. 1.3 Units-The values stated in SI units are to be regarded as the standard. No other units of measurement...
4.1 The appearance of the various degrees of dry and wet abrasive blast cleaning, hand and power tool cleaning, and water jetting are influenced by the initial rust grades of the steel being cleaned and/or the type and condition of the coating on the existing steel. The...
3.1 Titanium dioxide is used in rubber compounding as a colorant to impart whiteness to any desired end product. It is used in sidewalls of automobile tires. 3.2 It is chemically inert and slightly basic with a pH of 7.0 to 8.0. The free-chalking, weathering properties of anatase titanium-dioxide...
This practice covers the testing of the integrity of high-efficiency particulate air (HEPA) filters installed in laminar flow clean rooms of the ceiling to floor or wall to wall type, and laminar flow clean work stations using condensation nuclei detector. The recommended practice may...
5.1 This test method is used for measuring ammonia and ammonium ion in water samples and soil or plant extracts. 5.2 Ammonia compounds are widely distributed in the environment and may be applied as fertilizer, used as cleaning compounds, or used in water treatment. 5.3 Ammonia nitrogen...
4.1 Proper bonding of coatings and linings to concrete surfaces requires proper cleaning and frequently requires the concrete to be roughened to increase the surface area. The roughness, also known as surface profile, can be imparted into concrete by abrasive blast cleaning, acid...
Note 1: Throughout the practice, "gear" means gear or pinion unless the gear is specifically identified. 1.1 This practice describes a two-part procedure for examination of gear teeth on mill and kiln gear drives and pinions using eddy current array (ECA) methods. The first part of this practice...
1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants...
1.1 This test method covers the determination of the resistance to the formation of pills and other related surface changes on textile fabrics using the Martindale tester. Note 1: For other methods, if testing the pilling resistance of textiles, refer to Test Methods D3511/D3511M, D3512/D3512M, and...
1.1 This practice uses dilute nitric acid to clean glass and plastic labware used in laboratories preparing and analyzing samples for metal and metalloid content. 1.2 Practice D5245 describes cleaning labware used in microbiological analyses. Practice D8589 describes cleaning...
5.1 The atomizer test as described in this test method is rapid, nondestructive, and may be used for control and evaluation of processes for the removal of hydrophobic contaminants. The test may also be used for the detection and control of hydrophobic contaminants in processing environments. For...
1.1 This practice covers procedures to evaluate the compatibility of coatings with additives used to prevent flash rusting of steel before application of coatings. 1.2 The additives are used with vapor blast, wet abrasive blast (WAB), low or high pressure water cleaning (LPWC, HPWC), and...
5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning and exposure) during manufacture and service that can mar their surface. The ability of high gloss coatings to maintain their...
This guide provides information on the deposition of engineering chromium by electroplating. This is sometimes called "functional" or "hard" chromium and is usually applied directly to the basis metal and is usually thicker than decorative deposits. This guide is not intended as a standardized...
This specification covers the requirements for electrodeposited zinc nickel alloy coatings on metals. The zinc nickel coating shall be defined as Class 1. The five chromate conversion coating types shall be defined as follows: Type A shall be with colorless conversion coatings, Type B shall be with...
This consumer safety specification covers performance requirements, test methods, and labeling requirements to promote the safe use of baby changing tables and other changing surfaces such as contoured changing pads and add-on changing units that are sold separately for use on furniture products...
1.1 This guide provides recommendations for the care and maintenance of clothing that is flame resistant or arc rated. 1.2 These recommendations address the industrial laundering process. Industrial laundering is an effective cleaning process for flame resistant or arc rated clothing; follow...
1.1 This guide provides recommendations for home laundering of clothing that is flame resistant or arc rated. These recommendations address the home laundering process. Home laundering is an effective cleaning process for flame resistant or arc rated garments; follow all label care...
5.1 Coatings, particularly the high gloss coatings used on automobiles, boats, toys, etc., are subject to a wide variety of conditions (for example, wiping, cleaning, and exposure) that can mar their surface. The ability of these coatings to maintain their appearance is an important product...
1.1 This test method covers the determination of the fineness of hydraulic cement by means of the 45-μm (No. 325) sieve. 1.1.1 This test method may be used for the determination of the fineness of other materials. However, certain requirements, such as calibration procedures, cleaning of...