loading
ASTM D5790-18(2026) - Standard Test Method for Measurement of Purgeable Organic Compounds in Water by Capillary Column Gas Chromatography/Mass Spectrometry
July 1, 2026 - ASTM International

1.1 This test method covers the identification and simultaneous measurement of purgeable volatile organic compounds. It has been validated for treated drinking water, wastewater, and ground water. This test method is not limited to these particular aqueous matrices; however, the applicability of...

ASTM E260-96(2026) - Standard Practice for Packed Column Gas Chromatography
January 1, 2026 - ASTM International

1.1 This practice is intended to serve as a general guide to the application of gas chromatography (GC) with packed columns for the separation and analysis of vaporizable or gaseous organic and inorganic mixtures and as a reference for the writing and reporting of GC methods. Note 1: This...

ASTM D6387-19(2026) - Standard Test Methods for Composition of Turpentine and Related Terpene Products by Capillary Gas Chromatography
June 1, 2026 - ASTM International

5.1 Earlier methods for characterizing turpentine and related terpene products were based on physical properties, such as those in Specification D13 and Test Methods D801 and D802, and packed column gas chromatography for the major constituents (for example, a-pinene, ß-pinene) as in Test...

ASTM E1001-21(2026) - Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves
July 1, 2026 - ASTM International

1.1 This practice describes procedures for the ultrasonic examination of bulk materials or parts by transmitting pulsed, longitudinal waves through a liquid couplant into the material and observing the indications of reflected waves (see Fig. 1). It covers only examinations in which one search unit...

ASTM D4128-18(2026) - Standard Guide for Identification and Quantitation of Organic Compounds in Water by Combined Gas Chromatography and Electron Impact Mass Spectrometry
July 1, 2026 - ASTM International

1.1 This guide covers the identification and quantitation of organic compounds by gas chromatography/mass spectrometry (GC-MS) (electron impact) that are present or extracted from water and are capable of passing through a gas chromatograph without alteration. This guide can be used to provide...

ASTM D1987-22(2026) - Standard Test Method for Biological Clogging of Geotextile, Drainage Geocomposites, or Soil/Geotextile Filters
June 1, 2026 - ASTM International

5.1 This test method is performance oriented for determining if, and to what degree, different liquids create biological activity on geotextile filters thereby reducing their flow capability. The use of the method is primarily oriented toward landfill leachates but can be performed with any liquid...

ASTM E3168-20a(2026) - Standard Practice for Determining Low-Contrast Visual Acuity of Radiographic Interpreters
July 1, 2026 - ASTM International

1.1 This practice details the procedure for determining the low-contrast visual acuity of a radiographic interpreter by evaluating the ability of the individual to detect linear images of varying radiographic noise, contrast, and sharpness. No statement is made regarding the applicability of these...

ASTM D6730-26 - Standard Test Method for Determination of Individual Components in Spark Ignition Engine Fuels by 100-Metre Capillary (with Precolumn) High-Resolution Gas Chromatography
May 1, 2026 - ASTM International

5.1 Knowledge of the individual component composition (speciation) of gasoline fuels and blending stocks is useful for refinery quality control and product specification. Process control and product specification compliance for many individual hydrocarbons can be determined through the use of this...

ASTM E3248-26 - Standard Guide for Non-Aqueous Phase Liquid (NAPL) Mobility and Migration in Sediment—Conceptual Models for NAPL Emplacement and Influence on NAPL Movement
May 15, 2026 - ASTM International

1.1 This guide is designed for application at a wide range of sediment sites where non-aqueous phase liquid (NAPL) is present or suspected to be present. This guide describes emplacement mechanisms that can result in NAPL presence within sediment and how the characteristics of the sediment, aquatic...

ASTM D751-26 - Standard Test Methods for Coated Fabrics
June 1, 2026 - ASTM International

1.1 These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. 1.2 The scope of each of these test methods appears in the section in which the test method is described. 1.3 The test methods appear in the following sections: Test...

ASTM E2032-26 - Standard Practice for Extension of Data From Fire Resistance Tests Conducted in Accordance with ASTM E?119
June 1, 2026 - ASTM International

1.1 This practice covers the extension of fire resistance ratings obtained from fire tests performed in accordance with Test Method E119 to constructions that have not been tested. Test Method E119 evaluates the duration for which test specimens will contain a fire, retain their standard integrity,...

ASTM C1935-26 - Standard Practice for Installation Methods for Adhered Veneer Systems Using Thin Brick Units Made from Clay or Shale
June 1, 2026 - ASTM International

1.1 This practice is intended to provide accepted installation procedures for thin brick units in adhered veneer systems in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of clay and shale thin brick...

ASTM D3606-26 - Standard Test Method for Determination of Benzene and Toluene in Spark Ignition Fuels by Gas Chromatography
May 1, 2026 - ASTM International

1.1 This test method covers the quantitation in liquid volume percent of benzene and toluene in finished motor and aviation spark ignition fuels by gas chromatography. This test method has two procedures: Procedure A uses capillary column gas chromatography and Procedure B uses packed...

ASTM E3300-26 - Standard Guide for Non-Aqueous Phase Liquid (NAPL) Mobility and Migration in Sediment—Factors Affecting Ebullition and Evaluating Ebullition Activity and the Associated Ebullition-Facilitated Transport of NAPL/Contaminants
April 1, 2026 - ASTM International

1.1 Many contaminants (such as petroleum products and coal tar) are emplaced in sediment in the form of an immiscible liquid, known as a non-aqueous phase liquid (NAPL). NAPL can either be a light non-aqueous phase liquid (LNAPL) that is less dense than water or a dense non-aqueous phase liquid...

ASTM D8236-26 - Standard Practice for Preparing an Equilibrium Liquid/Vapor Sample of Live Crude Oil, Condensates, or Liquid Petroleum Products Using a Manual Piston Cylinder for Subsequent Liquid Analysis or Gas Analysis
May 1, 2026 - ASTM International

5.1 This practice allows for compositional analysis of the gases in equilibrium with crude oil, condensate, and liquid petroleum products at a 4:1 vapor/liquid ratio at ambient temperature for analysis using typical instrumentation (RGA) already available in typical refinery laboratories. These...

ASTM D8342/D8342M-21(2026) - Standard Test Method for Measuring the Probability of a Full Length Burn on a Cannabis/Hemp Pre-roll
April 15, 2026 - ASTM International

1.1 This fire-test-response standard provides a standard measure of the probability of a cannabis/hemp pre-roll positioned on a substrate to generate enough heat to continue burning and thus potentially cause ignition of bedding or upholstered furniture. 1.2 This test method shall be applicable to...

ASTM E1151-93(2026) - Standard Practice for Ion Chromatography Terms and Relationships
January 1, 2026 - ASTM International

This practice deals primarily with identifying the terms and relationships of those techniques that use ion exchange chromatography to separate mixtures and a conductivity detector to detect the separated components. However, most of the terms should also apply to ion chromatographic techniques...

ASTM B761-26 - Standard Test Method for Particle Size Distribution of Metal Powders and Related Compounds by X-Ray Monitoring of Gravity Sedimentation
May 1, 2026 - ASTM International

1.1 This test method covers the determination of particle size distributions of metal powders. Experience has shown that this test method is satisfactory for the analysis of elemental tungsten, tungsten carbide, molybdenum, and tantalum powders, all with an as-supplied estimated average particle...

ASTM D1937-26 - Standard Test Method for Carbon Black, Pelleted—Mass Strength
April 1, 2026 - ASTM International

1.1 This test method covers the determination of the mass strength of pelleted carbon black. It is designed to determine the force required to pack a cylindrical column of pelleted carbon black. The results of this test are believed to relate to the ability of the carbon black to flow in...

ASTM D3525-20(2026)e1 - Standard Test Method for Gasoline Fuel Dilution in Used Gasoline Engine Oils by Wide-Bore Capillary Gas Chromatography
March 15, 2026 - ASTM International

1.1 This test method describes a gas chromatographic technique for determining the amount of gasoline fuel dilution in used lubricating oils arising from their use in gasoline engines. 1.2 This test method is limited to gas chromatographs accommodating wide-bore (0.53?mm) capillary columns...

Advertisement