1.1 This specification describes the required properties and test methods for a one or two-component, cold liquid-applied elastomeric-type membrane comprised of silyl-terminated polyether polymer, silyl-terminated polyurethane polymer, or a blend of the two polymers for waterproofing building...
1.1 These test methods cover transverse load testing to determine the structural properties of wall segments. 1.2 These test methods serve to evaluate the performance of wall panels subject to transverse bending loads applied perpendicular to the plane of the wall. The tests are conducted on...
4.1 This guide discusses various methods for evaluating the surface of structural concrete roof decks to receive adhered roofing system materials. 4.2 Methods for evaluating the surface of structural concrete roof decks to receive adhered roofing system materials included as part of a...
1.1 This guide provides recommended procedures for the installation of hot-applied rubberized asphalt (HRA) membrane for roofing and waterproofing applications in areas where it will be protected from sunlight and potential physical damage. 1.2 This guide applies to fabric-reinforced HRA membranes...
1.1 This guide describes the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C836/C836M, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is...
1.1 This specification describes the required properties and test methods for a one or two-component, cold liquid-applied elastomeric-type membrane comprised of silyl-terminated polyether polymer, silyl-terminated polyurethane polymer, or a blend of the two polymers for waterproofing building...
1.1 This practice provides a standard set of procedures for inspecting and reporting on the installed board and wrap type fireproofing materials applied to structural steel or other substrates used in buildings. 1.2 This practice establishes procedures to inspect products and systems, including...
1.1 This practice covers a standard procedure for inspecting the coating system of a ship's topside and superstructure, tanks and voids, decks and deck machinery, and underwater hull and boottop during drydocking. Included are a standard inspection form to be used for reporting the...
1.1 This performance specification covers performance requirements for vinyl-coated and urethane-coated upholstery fabrics produced with woven, knit, or nonwoven substrates which are used in the manufacture of new indoor furniture. 1.2 This performance specification is not applicable to fabrics...
5.1 The impact sound rating for a floor assembly is determined both by the basic floor assembly and the floor covering on the upper surface. The same floor covering in combination with different basic floor assemblies will not always give the same impact insulation class (IIC) and high-frequency...
4.1 Tests and criteria as outlined determine the overall usability and stability of chairs in an environment simulating the conditions of use. 4.2 Tests simulate two types of surfaces: 4.2.1 Smooth surfaces such as linoleum, wet pool decks, etc. The glass testing base (see Fig. 2) is used to...
4.1 The failure to correct membrane defects during and as soon as possible after its installation can cause premature failure of the membrane. Problems include design deficiencies, faulty application of the membrane system, and damage by subsequent trades.4 Roof designs incorporating a waterproof...
1.1 This specification covers non-asbestos fiber-mat reinforced cementitious backer units manufactured to be dimensionally stable and suitable as either an unfinished substrate (see Note 1) or as a substrate for decoration such as natural stone or tile on walls, floors, or decks in wet and...
1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric membrane for waterproofing building decks not subject to hydrostatic pressure. The specification applies only to a membrane system that has an integral wearing surface. This...
1.1 The purpose of this guide is to provide guidance in the selection of a suitable waterproofing membrane within a vegetative roof system. The guide offers various options for reviewing the membrane installation during and upon completion of the installation and prior to the vegetative components...
5.1 Silica sand produces a slower rate of abrasion for organic coatings than that provided by silicon carbide. For some types of coatings, it may also provide greater differentiation. 5.2 The abrasion resistance scales produced by the two methods differ, but the methods provide approximately the...
1.1 This specification covers the material, testing, and application requirements for a field-molded asphaltic plug joint (APJ) used in expansion joint sealing on asphalt concrete overlay and portland cement concrete decks. The scope of this specification is limited to field-molded APJ. This...
5.1 Energy conservation is being addressed more often on existing or historically significant buildings, or both, originally constructed with uninsulated or unconditioned roof enclosures, or both. Renovations or retrofits of existing buildings that include altering the roof enclosure or changing...
Narrow Your Results