loading
ASTM F3359/F3359M-21(2026) - Standard Test Method for Determining Bending Yield Moment of Staples
May 1, 2026 - ASTM International

5.1 Staples are mechanical fasteners used in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded staple connections use a yield theory to establish nominal resistance (Note 2). In order to develop nominal resistance for laterally-loaded stapled...

ASTM D751-26 - Standard Test Methods for Coated Fabrics
June 1, 2026 - ASTM International

1.1 These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products. 1.2 The scope of each of these test methods appears in the section in which the test method is described. 1.3 The test methods appear in the following sections: Test...

ASTM D7949-25 - Standard Test Methods for Integrity Testing of Concrete Deep Foundations by Thermal Methods
May 1, 2025 - ASTM International

1.1 These test methods provide procedures for measuring the temperature profile within a deep foundation element constructed using cast-in-place concrete, such as bored piles, drilled shafts, augered piles, diaphragm walls, barrettes, and alike. The thermal profile induced by the curing...

ASTM D6976-13(2024) - Standard Specification for Rubber Contraceptives—Vaginal Diaphragms
December 1, 2024 - ASTM International

1.1 This specification covers requirements for contraceptive vaginal diaphragms, hereafter called diaphragms. 1.2 Vaginal barrier devices known as cervical caps, vaginal sponges and female condoms are not included in this specification. 1.3 This international standard was developed in...

ASTM E1787-25 - Standard Test Method for Anions in Caustic Soda and Caustic Potash (Sodium Hydroxide and Potassium Hydroxide) by Ion Chromatography
February 1, 2025 - ASTM International

1.1 This test method covers the determination of anionic impurities in 50?% caustic soda (sodium hydroxide) and 50?% caustic potash (potassium hydroxide) solutions using ion chromatography (IC). Anions that can be determined at concentrations of approximately 0.1?μg/g up to 1000?μg/g (ppm) include:...

ASTM F1565-00(2024) - Standard Specification for Pressure-Reducing Valves for Steam Service
November 15, 2024 - ASTM International

1.1 This specification covers self-contained, internally operated, globe style, pressure-reducing valves for use in steam service. In these valves, the downstream pressure feedback is sensed by a spring-loaded diaphragm to position a pilot valve-the pilot valve uses the inlet steam pressure...

ASTM D7999-15(2024) - Standard Classification for Rubber Products in Natural Gas Pipeline Applications
November 1, 2024 - ASTM International

1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic robbers, alone or in combination) that are intended for use in rubber products found in natural gas pipeline applications (for example, elastomeric couplings, o-rings,...

ASTM C1858/C1858M-24 - Standard Practice for Design, Construction, and Material Requirements for Direct Hung Suspended T-bar Type Ceiling Systems Intended to Receive Gypsum Panel Products in Areas Subject to Earthquake Ground Motions
May 1, 2024 - ASTM International

5.1 This practice provides a standardized installation procedure for ceilings designed and installed as a diaphragm. When installed according to this practice, these ceilings have sufficient strength to resist seismic forces without lateral force bracing.

ASTM D1044-24 - Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion by the Taber Abraser
June 1, 2024 - ASTM International

4.1 Transparent plastic materials, when used as windows or enclosures, are subject to wiping and cleaning; hence the maintenance of optical quality of a material after abrasion is important. It is the purpose of this test method to provide a means of estimating the resistance of such materials to...

ASTM D3786/D3786M-18(2023) - Standard Test Method for Bursting Strength of Textile Fabrics—Diaphragm Bursting Strength Tester Method
June 1, 2023 - ASTM International

5.1 This method for the determination of diaphragm bursting strength of knitted, nonwoven and woven fabrics is being used by the textile industry for the evaluation of a wide variety of end uses. 5.2 In cases where test results obtained using the procedures in Test Method D3786 have not been...

MSS SP 88 - Diaphragm Valves
January 1, 2021 - MSS

This Standard Practice applies to valves for general liquid and gas service that effect valve closure by means of a resilient diaphragm sealing against a weir or a diaphragm acting in conjunction with a separate or integral disk-member sealing against a seat, having equal sealing...

ASTM E2322-22 - Standard Test Method for Conducting Transverse and Concentrated Load Tests on Panels used in Floor and Roof Construction
October 1, 2022 - ASTM International

4.1 Transverse Load-The procedures outlined will serve to evaluate the performance of floor and roof segments for deflection, permanent set and ultimate capacity. Performance criteria based on data from these procedures can ensure structural adequacy and effective service. 4.2 Concentrated...

ASTM F2070-00(2022) - Standard Specification for Transducers, Pressure and Differential, Pressure, Electrical and Fiber-Optic
October 1, 2022 - ASTM International

This specification covers the requirements for pressure and differential pressure transducers for general applications. Pressure transducers typically consist of a sensing element that is in contact with the process medium and a transduction element that modifies the signal from the sensing element...

ASTM D3886-22 - Standard Test Method for Abrasion Resistance of Textile Fabrics (Inflated Diaphragm Apparatus)
February 1, 2022 - ASTM International

1.1 This test method2 covers the determination of the resistance to abrasion of woven and knitted textile fabrics, both conditioned and wet, using the inflated diaphragm tester. This procedure is not applicable to floor coverings. Note 1: Other procedures for measuring the abrasion...

ASTM E1803-14(2022) - Standard Test Methods for Determining Strength Capacities of Structural Insulated Panels
May 1, 2022 - ASTM International

1.1 These test methods cover procedures for determining strength properties under specified loads for rigid-faced structural insulated panels. These test methods are appropriate for structural insulated panels with rigid facings having a minimum thickness of 0.16 in. (4 mm) and an insulating core...

ASTM C1858-17a(2021) - Standard Practice for Design, Construction, and Material Requirements for Direct Hung Suspended T-bar Type Ceiling Systems Intended to Receive Gypsum Panel Products in Areas Subject to Earthquake Ground Motions
December 1, 2021 - ASTM International

5.1 This practice provides a standardized installation procedure for ceilings designed and installed as a diaphragm. When installed according to this practice, these ceilings have sufficient strength to resist seismic forces without lateral force bracing.

ASTM F3359/F3359M-21 - Standard Test Method for Determining Bending Yield Moment of Staples
December 1, 2021 - ASTM International

5.1 Staples are mechanical fasteners used in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded staple connections use a yield theory to establish nominal resistance (Note 2). In order to develop nominal resistance for laterally-loaded stapled...

ASTM D2210-21 - Standard Test Method for Grain Crack and Extension of Leather by the Mullen Test
December 1, 2021 - ASTM International

4.1 The test method is designed to measure the force required to crack the grain of leather by steady hydraulic pressure on a diaphragm of definite diameter applied to the flesh side of the specimen to form a sphere. The cracking of the grain is a result of failure under elongation or...

ASTM D8381/D8381M-21 - Standard Test Methods for Measuring the Depth of Deep Foundations by Parallel Seismic Logging
November 1, 2021 - ASTM International

1.1 The test Methods described in this standard are used to measure the depth of vertical deep foundation elements including micropiles, driven piles (prefabricated or cast in-situ), bored piles, secant or tangent pile walls, caissons, barrettes, diaphragm walls and sheet pile walls. It is...

PIP PHSMV022 - Hygienic Stainless Steel Diaphragm Valve Descriptions
January 1, 2020 - PIP

This Practice provides requirements for suppliers providing hygienic stainless steel diaphragm valves included in PIP Piping Line Class Material Specifications.

Advertisement