1.1 This test method provides procedures for validating temperature and enthalpy measurements of differential scanning calorimeters (DSC) and analytical methods based upon the measurement of temperature or enthalpy (or heat), or both, by DSC. Performance parameters determined include...
1.1 This practice describes the calculation of the heat of vaporization of a liquid or the heat of sublimation of a solid from measured vapor pressure data. It is applicable to pure liquids, azeotropes, pure solids, and homogenous solid solutions over the temperature range for which the vapor...
5.1 The equipment, test duration, and technique should be determined before commencement of the test based on the required test sensitivity or accuracy (see Annex A1 and Annex A2). If the test is used to certify that the vessel has a maximum specified leakage rate, then the test equipment and test...
5.1 Thermogravimetry provides a rapid method for determining the thermal decomposition and reaction mass change of a material. 5.2 This test method is useful in detecting potentially hazardous reactions and in estimating the temperatures at which these reactions occur. This test method is...
1.1 This specification covers the general requirements that, unless otherwise specified in the product specification, apply to steel sheet in coils and cut lengths, metallic-coated on continuous lines by the hot-dip process. The product is intended for applications requiring corrosion resistance....
1.1 These test methods cover the determination of the amounts of a-pinene, ß-pinene, dipentene, terpene alcohols, and other terpene compounds in turpentine and related terpene products using capillary gas chromatography. The two methods for determining the amount of the individual terpene compounds...
4.1 The ENDF/B library in the United States and similar libraries elsewhere, such as JEFF (21), JENDL (22), and BROND (24), provide a compilation of neutron cross section and other nuclear data for use by the nuclear community. The availability of these excellent evaluations makes possible a...
1.1 This test method covers a standard laboratory procedure for determining the air leakage rates of exterior windows, skylights, curtain walls, and doors under specified differential pressure conditions across the specimen. The test method described is for tests with constant temperature...
1.1 This test method covers a procedure for measuring the hardness of vulcanized or thermoplastic rubber. The hardness is obtained by the difference in penetration depth of a specified dimension ball under two conditions of contact with the rubber: (1) with a small initial force and (2) with a much...
1.1 Process validation of sterilizing filtration is required by industry standards and regulatory agencies to ensure that process fluid contact with the filter under actual worst-case process-use conditions (that is, time, flux, temperature, and pressure differential) do not adversely affect...
1.1 This specification defines general specifications for heat meters. Heat meters are instruments that measure heat in heat exchange circuits in which energy is absorbed (cooling) or given up (heating) by a flowing liquid. 1.2 For this specification, the necessary elements of a heat meter consist...
1.1 This test method is for the determination of the inherent viscosity of poly(ethylene terephthalate) (PET) soluble at 0.50?% concentration in a 60/40 phenol/1,1,2,2-tetra
This specification covers the classifications, performance requirements, and test methods for the materials used in the construction of medical face masks that are used in health care services such as surgery and patient care. Medical face mask material performance is based on testing for bacterial...
1.1 This test method covers the procedure for rating the tendencies of gas turbine fuels to deposit decomposition products within the fuel system. 1.2 The differential pressure values in mm Hg are defined only in terms of this test method. 1.3 The deposition values stated in SI units shall...
1.1 This test method describes the temperature calibration of differential scanning calorimeters (DSCs) on cooling using the difference between transition temperatures upon heating and cooling in the temperature range of 65 °C to 420 °C. Within this temperature range, an offset in the...
1.1 This test method covers determination of curing parameters of pultrusions resins by differential scanning calorimetry. 1.2 This test method is applicable to pultrusion resin solutions with adequate initiator(s). 1.3 The normal operating temperature range is from 0 to 200°C. Note 1: Resin...
1.1 This test method describes the determination of purity of materials greater than 98.5 mol % purity using differential scanning calorimetry and the van't Hoff equation. 1.2 This test method is applicable to thermally stable compounds with well-defined melting temperatures (that is, not...
5.1 Users of this test method must determine for themselves whether the practices described meet the requirements of local or national authorities regulating asbestos or other fibrous hazards (for example, the test method must be used within the parameters set out in Appendix A of the U.S. OSHA...
This specification covers seamless red brass pipe in all nominal pipe sizes, both regular and extra-strong. The pipe in the annealed temper shall be suitable for use in plumbing, boiler feed lines, and for similar purposes. In the drawn general purpose temper, the pipe shall be suitable for...
5.1 This practice is intended to evaluate the material performance after exposure to specified environmental factors. It is understood that these performance values are dependent upon these specified exposure periods and intensities of environmental factors. Other values are possible if the...
Narrow Your Results