loading
ASTM D1042-26 - Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture
July 1, 2026 - ASTM International

1.1 This test method is designed to provide a means for measuring the dimensional changes of plastic specimens such as shrinkage or expansion, developed under specific heat and water conditionings. 1.2 The values stated in SI units are to be regarded as standard. The values given in...

ASTM F2199-26 - Standard Test Method for Determining Dimensional Stability and Curling Properties of Resilient Flooring after Exposure to Heat
August 1, 2026 - ASTM International

4.1 The final appearance of an installed floor depends upon several factors. These include but are not limited to size and squareness in the case of tiles/planks, the quality of joint cut, the quality and preparation of the subfloor and the skill of the installer. Long term appearance of the...

ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

This specification covers requirements, test methods, and methods of marking for crosslinked polyethylene plastic hot- and cold-water distribution systems components made in one standard dimension ratio. Components are comprised of tubing and fittings intended for use in residential and...

ASTM F1674-18(2026) - Standard Test Method for Joint Restraint Products for Use with PVC Pipe
June 1, 2026 - ASTM International

4.1 This test method is useful for establishing any effects that a joint restraint product has on the performance of PVC pressure pipe. This test method is designed so that success in all three parts of the test provides reasonable assurance that a joint restraint product may be used on PVC pipe at...

ASTM D6164/D6164M-26 - Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements
July 1, 2026 - ASTM International

This specification covers Grades G (granule surfaced) and S (smooth surfaced) prefabricated bituminous sheet materials reinforced with polyester fabric and modified by styrene butadiene styrene (SBS) thermoplastic elastomer, intended for use in the fabrication of multiple ply roofing and...

ASTM D7477-16(2026) - Standard Test Method for Determining the Area Stability of Wet Blue Submersed in Boiling Water
July 1, 2026 - ASTM International

1.1 This test method provides a standard procedure for determination of the dimensional stability or area shrinkage of a specimen of Wet Blue that is submersed in boiling water for a specified time period. This test method is applicable to all types of Wet Blue. 1.2 The values given in SI...

ASTM C1954-26 - Standard Specification for Decorative Enamels on Flat Glass
July 1, 2026 - ASTM International

1.1 This specification covers the aesthetic quality requirements for decorative enamels applied to flat glass for use in building glazing. 1.2 This specification covers the requirements for flat glass, with either organic or ceramic enamels applied. 1.2.1 Glass may be annealed, heat-strengthened,...

ASTM D8366-21a(2026) - Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF
July 1, 2026 - ASTM International

1.1 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded sheet, rod and tubular bar manufactured from unfilled PVDF. 1.2 This specification covers the requirements and test methods for the material, dimensions,...

ASTM D6454/D6454M-26 - Standard Test Method for Determining the Short-Term Compression Behavior of Turf Reinforcement Mats (TRMs)
July 1, 2026 - ASTM International

5.1 The compression behavior test for TRMs is intended to be an index test. It is anticipated that the results of the compression behavior test will be used to evaluate product. The results of the analyses also may be used to compare the relative compressive yield points of materials that exhibit a...

ASTM B168-26 - Standard Specification for Nickel-Chromium-Aluminum Alloys, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy Plate, Sheet, and Strip
July 1, 2026 - ASTM International

This specification covers rolled plates, sheets, and strips made of nickel-chromium-iron alloys (UNS Nos. N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696) and nickel-chromium-cobalt-molybdenum alloys (UNS No. N06617). Materials shall be sampled and prepared, then tested...

ASTM D6456-10(2026) - Standard Specification for Finished Parts Made from Polyimide Resin
July 1, 2026 - ASTM International

1.1 This specification is intended to be a means of calling out finished plastic parts ready for industrial or consumer use. 1.2 This specification covers finished parts and shapes from which parts are machined, made from a semi-crystalline polyimide (PI). 1.3 This specification is intended to...

ASTM E3534-26 - Standard Test Method for Vacuum Insulating Glass Durability
July 1, 2026 - ASTM International

1.1 This test method covers procedures for testing the durability of preassembled, permanently sealed vacuum insulating glass (VIG) units. 1.2 This test method is applicable only to VIG units that are constructed with flat glass lites (glass panes). 1.3 This test method is applicable to units made...

ASTM E911-98(2026) - Standard Specification for Glass Stopcocks with Polytetrafluoroethylene (PTFE) Plugs
June 1, 2026 - ASTM International

1.1 This specification covers standard dimensional requirements for obtaining, within practical limits, interchangeability in glass stopcocks (Note 1) with polytetrafluoroethylene (PTFE) plugs for ordinary laboratory and industrial applications. It covers dimensional...

ASTM B443-26 - Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy and Nickel-Chromium-Molybdenum-Silicon Alloy Plate, Sheet, and Strip
July 1, 2026 - ASTM International

This specification covers rolled nickel-chromium-molybdenum-columbium alloy (UNS No. N06625) and nickel-chromium-molybdenum-silicon alloy (UNS No. N06219) plates, sheets, and strips. N06625 alloys shall be furnished in two grades of different heat treatment conditions, namely: Grade 1 (annealed);...

ASTM C119-26 - Standard Terminology Relating to Dimension Stone
August 1, 2026 - ASTM International
A description is not available for this item.
ASTM E960-93(2026) - Standard Specification for Laboratory Glass Beakers
June 1, 2026 - ASTM International

This specification provides standard dimensional requirements for glass beakers suitable for general laboratory use. The glass beakers are classified into types and sizes and are presented in details. The glass beaker types are: type I - low form with spout; type II - low form, with spout...

ASTM E2661/E2661M-26 - Standard Practice for Acoustic Emission Examination of Plate-like and Flat Panel Composite Structures Used in Aerospace Applications
July 1, 2026 - ASTM International

1.1 This practice covers acoustic emission (AE) examination or monitoring of panel and plate-like composite structures made entirely of fiber/polymer composites. 1.2 The AE examination detects emission sources and locates the region(s) within the composite structure where the emission originated....

ASTM A420/A420M-26 - Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
July 1, 2026 - ASTM International

This specification covers wrought carbon steel and alloy steel pipe fittings of seamless and welded construction for use in pressure piping and pressure vessel service at low temperatures. Materials shall consist of forgings, bars, plates, seamless or fusion welded tubular products with filler...

ASTM D4966-22(2026) - Standard Test Method for Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method)
July 1, 2026 - ASTM International

5.1 Acceptance Testing-this test method is not considered satisfactory for acceptance testing of commercial shipments of fabric. The between-laboratory precision of this test method is poor and, because of the nature of abrasion testing itself, technicians frequently fail to obtain results in...

ASTM C1782/C1782M-26 - Standard Specification for Segmental Concrete Paving Slabs
June 1, 2026 - ASTM International

This specification covers segmental concrete paving slabs manufactured for construction of pedestrian and roof applications for commercial and municipal projects where close dimensional tolerances for thickness, and/or length and width are not required. These slabs can be manufactured with a...

Advertisement