1.1 This guide is intended to be used by architects, engineers, specifiers, contractors, and material suppliers who design, select, specify, install, purchase, fabricate, or supply natural stone products for construction applications. 1.2 Consensus Standard-This guide is an industry consensus...
5.1 Tests made on a material under conditions herein prescribed are of considerable value in comparing the relative smoke obscuration characteristics of plastics. 5.2 This test method serves to determine the extent to which plastic materials are likely to smoke under conditions of active burning...
This test method details the standard procedures for the determination of the bond and cohesion of one-part elastomeric solvent release-type sealants after high- and low-temperature aging. The materials and apparatuses needed for this test procedure are an extension machine, a forced-draft...
4.1 The Form and Style for ASTM Standards manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee B05 recognizes the...
1.1 Specification D3924 defines a standard environment of 23?°C ± 2?°C and 50?% ± 5?% relative humidity and free from drafts for normal conditioning and testing of paint, varnish, lacquer, and related materials. This practice describes a test chamber that allows for control of relative...
1.1 This test method covers the measurement of the relative evaporation time of halogenated organic solvents and their admixtures. This test method is not applicable in the presence of excessive drafts or high-velocity air currents. 1.2 The values stated in SI units are to be regarded as...
5.1 This test method determines the response of leather to a standard ignition source, deriving measurement values for afterflame time, afterglow time, and char length. 5.2 The vertical flame resistance, as determined by this test method, only relates to a specified flame exposure and application...
5.1 This test method determines the response of leather to a standard ignition source, deriving measurement values for afterflame time, afterglow time, and char length. 5.2 The vertical flame resistance, as determined by this test method, only relates to a specified flame exposure and application...
1.1 This guide covers procedures for establishing a program to monitor the performance of Coating Service Level III lining (and coating) systems in operating nuclear power plants. Monitoring is an ongoing process of evaluating the condition of the in-service lining systems. 1.2 Coating Service...
This specification covers standardizing the dimensions and materials for the manufacture of steel or cast iron shear plates used in the fabrication of connections in wood constructions. This specification covers the two basic diameters of metal shear plates commonly used in North American timber...
This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. The steel shall conform to the required chemical composition requirements. The material shall...
5.1 This practice is used for drafting impact test specification requirements, and it presupposes no special familiarity with statistical methods. It provides for specification values that will pass acceptable lots with a high degree of certainty. The impact test requirement is intended to...
1.1 This test method describes the measurement of fiber cohesion as the dynamic cohesive force required to maintain drafting in rovings, slivers or tops when they are subjected to stress induced by passing between pairs of drafting rolls of different surface speeds. The cohesive force...
1.1 This guide describes and compares different methods for assessing the potential for, or existence of, depressurization-induced backdrafting and spillage from vented residential combustion appliances. 1.2 Assessment of depressurization-induced backdrafting and spillage is conducted under either...
1.1 This test method specifies a method for determining the flow characteristics of a fused thermosetting coating powder down a plane inclined at a set angle to the horizontal. This test method gives an indication of the degree of melt flow that may occur during the curing of the coating powder....
4.1 These test methods provide a measure of a shipping container's ability to protect a product from failure due to horizontal impacts. These measures are based on controlled levels of shock input and may be used for arriving at the optimum design of a container or system to protect a product...
1.1 This test method describes the measurement of fiber cohesion as the force required to cause initial drafting in a bundle of fibers in sliver and top. The observed cohesive force required to separate the fibers is converted to cohesive tenacity based on the linear density of the specimen....
4.1 The Form and Style Manual provides mandatory requirements and recommended practices for the preparation and content of ASTM specifications. In order to promote consistency in the style and content of product specifications under its jurisdiction, Committee A01 recognizes the need to provide a...
This specification defines standard environment for normal conditioning and testing of paint, varnish, lacquer, and related coating materials. Conditioning and testing of such materials shall be carried out in an atmosphere having room temperature and relative humidity within the limits of the...