loading
BS 308-1.4 - Technical Drawings - Scales
October 15, 1995 - BSI

SCOPE AND FIELD OF APPLICATION This International Standard specifies recommended scales and their designation for use on all technical drawings in any field of engineering.

ISO 5455 - Technical Drawings - Scales
January 1, 1979 - ISO

SCOPE AND FIELD OF APPLICATION This International Standard specifies recommended scales and their designation for use on all technical drawings in any field of engineering.

JIS Z 8314 - Technical Drawings - Scales
March 20, 1998 - JSA
A description is not available for this item.
BS EN ISO 5455 - Technical Drawings - Scales
October 15, 1995 - BSI
A description is not available for this item.
ISUZU ISA-K-041 - Technical drawings-Lines,lettering and scales of product drawing
December 20, 2019 - ISUZU

This standard covers the types of lines, lettering and scales that are used in product drawings drawn in orthographic representation. This standard is applicable to drawing other than product drawings (e.g. jig/tool drawings).

ASTM E3093-26 - Standard Guide for Structured Small Group Product Evaluations
February 1, 2026 - ASTM International

1.1 This guide covers those occasions in which a small group of individuals (generally between three and ten) with potentially different functional roles and degrees of training in sensory and product evaluation reviews a product or series of products for a specific objective, with a pre-identified...

ASTM D6031/D6031M-25 - Standard Test Method for Nuclear Gauge Logging In Situ Water Content and Density of Soil and Rock in Drilled Access Holes or Trenches Using Horizontal, Slanted, and Vertical Access Tubes
October 15, 2025 - ASTM International

1.1 This test method covers collection and comparison of logs of thermalized-neutron counts and back-scattered gamma counts along horizontal or vertical air-filled access tubes. 1.2 Access tubes are installed either by drilling access holes or digging a trench into the media being measured. 1.3 The...

ASTM C1089-19(2025) - Standard Specification for Spun Cast Prestressed Concrete Poles
June 1, 2025 - ASTM International

This specification covers spun cast prestressed concrete poles for use as structural supports for streetlights, traffic signals, and transmission, distribution, and communication lines. The acceptability of the poles shall be determined by the results of full-scale bending and torsional...

JIS DRAWING HDBK - JIS Drawing Handbook
January 1, 2019 - JSA
A description is not available for this item.
ASTM E2263-25 - Standard Test Method for Paired Preference Test
February 1, 2025 - ASTM International

5.1 The paired preference test determines whether or not there is a preference for one product over another product among a specific target population. Knowledge of consumer segments, brand loyalties, the range of product offerings in the marketplace, and the decision risk must be understood when...

ASTM A834-24 - Standard Specification for Common Requirements for Iron Castings for General Industrial Use
October 1, 2024 - ASTM International

This specification covers the standard common requirements for iron castings to be used for general industrial applications. The castings shall be made in a workman-like manner and shall conform to the dimensions on drawings furnished by the purchaser before manufacture is started. A lot...

ASTM E2263-24 - Standard Test Method for Paired Preference Test
March 15, 2024 - ASTM International

5.1 The paired preference test determines whether or not there is a preference for one product over another product among a specific target population. Knowledge of consumer segments, brand loyalties, the range of product offerings in the marketplace, and the decision risk must be understood when...

ASTM G134-17(2023) - Standard Test Method for Erosion of Solid Materials by Cavitating Liquid Jet
June 1, 2023 - ASTM International

5.1 This test method may be used to estimate the relative resistances of materials to cavitation erosion, as may be encountered for instance in pumps, hydraulic turbines, valves, hydraulic dynamometers and couplings, bearings, diesel engine cylinder liners, ship propellers, hydrofoils, internal...

ASTM E1694-22 - Standard Classification for Serviceability of an Office Facility for Special Facilities and Technologies
October 1, 2022 - ASTM International

1.1 This classification covers pairs of scales for classifying an aspect of the serviceability of an office facility, that is, the capability of an office facility to meet certain possible requirements for special facilities and technologies. 1.2 Each pair of scales, shown in Figs....

ASTM E1663-22 - Standard Classification for Serviceability of an Office Facility for Typical Office Information Technology
October 1, 2022 - ASTM International

4.1 Each Facility Rating Scale (see Figs. 1-18) in this classification provides a means to estimate the level of serviceability of a building or facility for one topic of serviceability and to compare that level against the level of any other building or facility. 4.2 This classification can...

ASTM E2669-22 - Standard Digital Reference Images for Titanium Castings
December 1, 2022 - ASTM International

1.1 The digital reference images provided in the adjuncts to this standard illustrate various types and degrees of discontinuities occurring in titanium castings.2 Use of this standard for the specification or grading of castings requires procurement of the appropriate adjunct digital reference...

ASTM F856-97(2022) - Standard Practice for Mechanical Symbols, Shipboard—Heating, Ventilation, and Air Conditioning (HVAC)
October 1, 2022 - ASTM International

1.1 This practice covers symbols used on heating, ventilation, and air conditioning (HVAC) detailed engineering drawings. 1.2 These symbols may be useful on contract and preliminary design drawings. 1.3 This international standard was developed in accordance with internationally...

ASTM B920-16(2022) - Standard Practice for Porosity in Gold and Palladium Alloy Coatings on Metal Substrates by Vapors of Sodium Hypochlorite Solution
October 1, 2022 - ASTM International

5.1 Palladium and gold coatings are often specified for the contacts of separable electrical connectors and other devices. Electrodeposits are the form of gold that is most used on contacts, although it is also employed as inlay or clad metal and as weldments on the contact surface. The intrinsic...

ASTM E384-22 - Standard Test Method for Microindentation Hardness of Materials
October 1, 2022 - ASTM International

5.1 Hardness tests have been found to be very useful for materials evaluation, quality control of manufacturing processes and research and development efforts. Hardness, although empirical in nature, can be correlated to tensile strength for many metals and alloys, and is also an indicator of...

ASTM D3363-22 - Standard Test Method for Film Hardness by Pencil Test
June 1, 2022 - ASTM International

1.1 This test method covers a procedure for rapid, inexpensive determination of the film hardness of an organic coating on a metal or similarly hard substrate in terms of drawing leads or pencil leads of known hardness. 1.2 This test method is similar in content (but not technically...

Advertisement