loading
ASTM E2425-21(2026) - Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers
July 1, 2026 - ASTM International

5.1 This test method demonstrates conformity of a dynamic mechanical analyzer at an isothermal temperature of 21 °C. 5.2 Dynamic mechanical analysis experiments often use linear temperature change. This test method does not address the effect of that change in temperature on the loss...

ASTM E3301-26 - Standard Test Method for Temperature Calibration of Dynamic Mechanical Analyzers Using Thermal Lag
July 1, 2026 - ASTM International

5.1 Dynamic mechanical analysis monitors changes in the viscoelastic properties (that is, storage modulus, loss modulus, tangent angle delta) of a material as a function of temperature and frequency, providing a means to quantify these changes. In many cases, the value to be assigned is the...

ASTM D7483-26 - Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
July 1, 2026 - ASTM International

1.1 This test method covers the measurement of dynamic viscosity and derivation of kinematic viscosity of liquids, such as new and in-service lubricating oils, by means of an oscillating piston viscometer. 1.2 This test method is applicable to Newtonian and non-Newtonian liquids; however the...

ASTM D445-26 - Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
July 1, 2026 - ASTM International

1.1 This test method specifies a procedure for the determination of the kinematic viscosity, ?, of liquid petroleum products, both transparent and opaque, by measuring the time for a volume of liquid to flow under gravity through a calibrated glass capillary viscometer. The dynamic...

ASTM D7945-26 - Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer
July 1, 2026 - ASTM International

1.1 This test method covers the measurement of dynamic viscosity and density for the purpose of derivation of kinematic viscosity of petroleum liquids, both transparent and opaque. The kinematic viscosity, ?, in this test method is derived by dividing the dynamic viscosity, ?, by the...

ASTM C1198-20(2026) - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Sonic Resonance
June 1, 2026 - ASTM International

1.1 This test method covers the determination of the dynamic elastic properties of advanced ceramics. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. Therefore, the...

ASTM C1259-21(2026) - Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio for Advanced Ceramics by Impulse Excitation of Vibration
June 1, 2026 - ASTM International

1.1 This test method covers determination of the dynamic elastic properties of advanced ceramics at ambient temperatures. Specimens of these materials possess specific mechanical resonant frequencies that are determined by the elastic modulus, mass, and geometry of the test specimen. The...

ASTM B777-15(2026) - Standard Specification for Tungsten Base, High-Density Metal
July 1, 2026 - ASTM International

This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with...

ASTM D8667-26 - Standard Test Method for Determining Intermediate and Low-Temperature Rheological Properties of Asphalt Binders Using a Dynamic Shear Rheometer (DSR)
May 1, 2026 - ASTM International

1.1 This test method covers the determination of parameters calculated from the measurement of modulus (G*) and phase angle (d) of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry in accordance with Test Method D7175. These parameters are considered...

ASTM E3543-26 - Standard Practice for Evaluating Bactericidal Activity of Nonporous, Semi-porous, and Hydrophobic Antimicrobial Surface Products Used Indoors
July 1, 2026 - ASTM International

1.1 This practice covers bactericidal claims for non-food-contact antimicrobial surfaces. 1.2 This practice is applicable to a wide range of surfaces, including nonporous, semi-porous, and hydrophobic surfaces. 1.3 This practice is also applicable for determining the efficacy of additives...

ASTM C1368-18(2026) - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Rate Strength Testing at Ambient Temperature
June 1, 2026 - ASTM International

1.1 This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress rate rectangular beam flexural testing, ring-on-ring biaxial disk flexural testing, or direct tensile strength, in which strength is determined as a function of applied...

ASTM D8668-26 - Standard Test Method for Determining the Peak Stress Energy and Shear Fatigue Resistance of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) Monotonic Shear Strength (MOSS) Test
May 1, 2026 - ASTM International

1.1 This test method covers the determination of asphalt binder peak stress (tf), peak stress energy (Ef), and peak strain (?f) using the monotonic shear strength (MOSS) test. tf, Ef, and ?f can be used to measure the strength, toughness, and strain tolerance of an asphalt binder under constant...

ASTM D8059-26 - Standard Test Method for Rubber Compounds—Measurement of Unvulcanized Dynamic Strain Softening (Payne Effect) Using Sealed Cavity Rotorless Shear Rheometers
June 1, 2026 - ASTM International

5.1 This test method is used to measure viscoelastic properties through the strain softening effects of a strain amplitude sweep (the Payne Effect). 5.2 For the uncured state, the time conditioning and strain amplitude strain sweeps can relate to colloidal silica particle or carbon black...

ASTM F3306-26 - Standard Test Method for Ion Release Evaluation of Medical Implants
June 1, 2026 - ASTM International

1.1 This test method assesses metal or other ions released from single-use, metallic, implantable medical devices or components thereof by exposing the device to solutions simulating the in vivo environment and temperature in a container for a predetermined time frame with regular sampling at...

ASTM C1465-26 - Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
June 1, 2026 - ASTM International

1.1 This test method covers the determination of slow crack growth (SCG) parameters of advanced ceramics by using constant stress-rate flexural testing in which flexural strength is determined as a function of applied stress rate in a given environment at elevated temperatures. The strength...

ASTM D4935-18(2026) - Standard Test Method for Measuring the Electromagnetic Shielding Effectiveness of Planar Materials
June 1, 2026 - ASTM International

4.1 This test method applies to the measurement of SE of planar materials under normal incidence, far-field, plane-wave conditions (E and H tangential to the surface of the material). 4.2 The uncertainty of the measured SE values is a function of material, mismatches throughout the transmission...

ASTM E3001-20(2026) - Standard Practice for Workforce Education in Nanotechnology Characterization
June 1, 2026 - ASTM International

5.1 This practice establishes the basic structure for education in the characterization of nanoscale materials at the undergraduate college level. The approach taken is to classify specific characterization methods into two tiers, with a minimum number of methods to be selected from each tier and...

ASTM E3034-20(2026) - Standard Guide for Workforce Education in Nanotechnology Pattern Generation
June 1, 2026 - ASTM International

5.1 The purpose of this guide is to provide a basic educational structure for pattern generation in nanotechnology to organizations developing or carrying out education programs for the nanotechnology workforce. This guide helps to describe the minimum knowledge base for anyone involved in...

ASTM E2996-20(2026) - Standard Guide for Workforce Education in Nanotechnology Health and Safety
June 1, 2026 - ASTM International

5.1 This guide is to provide, at the undergraduate college level, a basic educational structure in the health and safety aspects of nanotechnology to organizations developing or carrying out education programs for the nanotechnology workforce. This guide helps to describe the minimum knowledge base...

Advertisement