loading
ASTM D2847-22(2026) - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
August 1, 2026 - ASTM International

5.1 The data obtained from the use of this practice will provide a basis for the evaluation of coolant performance in passenger car, and light-duty truck service (according to the test chosen). The data obtained may also be used to provide added significance to the data obtained from simulated...

ASTM D4340-26 - Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions
April 1, 2026 - ASTM International

4.1 It is essential that engine coolants prevent heat-transfer corrosion of aluminum cylinder heads during engine operation. Any corrosion products formed may deposit on interior radiator surfaces, reducing heat-transfer efficiency of the radiator. Overheating and boil-over of the cooling system...

ASTM D6201-25 - Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
November 1, 2025 - ASTM International

1.1 This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels.2 This test method uses a Ford Ranger 2.3?L four-cylinder engine. This test method includes detailed information regarding the procedure,...

ASTM D2758-25 - Standard Test Method for Engine Coolants by Engine Dynamometer
September 1, 2025 - ASTM International

4.1 This test method provides a laboratory technique capable of reproducing the complex environmental stresses a coolant encounters under actual engine operating conditions. The test method provides improved discrimination over glassware and simulated service tests and improved correlation with...

ASTM D8114-25 - Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition
July 1, 2025 - ASTM International

1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a...

ASTM D8226-25 - Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIF Spark Ignition Engine
July 1, 2025 - ASTM International

1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856?kg or less. The tests are conducted using a specified spark-ignition engine with a...

ASTM D7935-24 - Standard Test Method for Corrosion Test for Non-Aqueous Engine Coolants in Glassware
September 1, 2024 - ASTM International

5.1 This test method will generally distinguish between non-aqueous engine coolants that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion...

ASTM D7935-24e1 - Standard Test Method for Corrosion Test for Non-Aqueous Engine Coolants in Glassware
September 1, 2024 - ASTM International

5.1 This test method will generally distinguish between non-aqueous engine coolants that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion...

ASTM D7820-19(2024) - Standard Test Method for Engine Coolant Corrosion Protection Under Accelerated Thermal and Oxidizing Conditions Using a Rotating Pressure Vessel
March 1, 2024 - ASTM International

4.1 Engines operating under severe conditions involving high temperatures, hot spot areas, entrained air, or small cooling systems, or combinations thereof, are placing greater emphasis on engine coolant oxidation stability and corrosion protection. This test method provides an accelerated test...

J2522_202312 - Inertia Dynamometer Disc and Drum Brake Effectiveness Test Procedure
December 13, 2023 - SAE International

This SAE Recommended Practice establishes a standard method to perform screening test sequences that identify a brake friction material's effectiveness under various test conditions. The result is an evaluation of brake friction material effectiveness under a set of defined braking conditions...

J3080_202312 - Inertia Dynamometer Rotor Crack Test Procedure for Air Disc Brakes
December 12, 2023 - SAE International

This Recommended Practice applies to commercial vehicles equipped with air disc brakes and above 4536 kg of Gross Vehicle Weight Rating. Other assessments on the friction material or rotor related to wear, durability, correlation to product life, noise, judder, compliance to specific regulations,...

ASTM D1384-24 - Standard Test Method for Corrosion Test for Engine Coolants in Glassware
January 1, 2024 - ASTM International

5.1 This test method will generally distinguish between coolants that are definitely deleterious from the corrosion standpoint and those that are suitable for further evaluation. However, the results of this test method cannot stand alone as evidence of satisfactory corrosion inhibition. The actual...

J2264_202301 - Chassis Dynamometer Simulation of Road Load Using Coastdown Techniques
January 13, 2023 - SAE International

This procedure covers vehicle operation and electric dynamometer (dyno) load coefficient adjustment to simulate track road load within dynamometer inertia and road load simulation capabilities.

ASTM D8114-23a - Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition
October 1, 2023 - ASTM International

1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a...

J2789_202304 - Inertia Calculation for Single-Ended Inertia-Dynamometer Testing
April 12, 2023 - SAE International

This procedure provides methods to determine the appropriate inertia values for all passenger cars and light trucks up to 4540 kg of GVWR. For the same vehicle application and axle (front or rear), different tests sections or brake applications may use different inertia values to reflect the...

J3213_202306 - Brake Dynamometer Squeal Noise Test Procedure for Commercial Vehicles with Air Brakes
June 2, 2023 - SAE International

This SAE Recommended Practice applies to commercial vehicles above 4540 kg of gross vehicle weight rating equipped with air brakes used under normal operating conditions. The procedure incorporates high and low-temperature test matrices, but does not fully account for the effects of the environment...

ASTM D8114-23 - Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition
July 1, 2023 - ASTM International

1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a...

J643_202308 - Hydrodynamic Drive Test Code
August 1, 2023 - SAE International

The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus...

ASTM C722-18(2023) - Standard Specification for Chemical-Resistant Monolithic Floor Surfacings
June 1, 2023 - ASTM International

This specification covers the requirements for aggregate-filled, resin-based, monolithic surfacing for use over concrete floors in areas where chemical resistance and the protection of concrete are required. The application methods for these floor surfacing shall include troweled, broadcast, slurry...

ASTM G134-17(2023) - Standard Test Method for Erosion of Solid Materials by Cavitating Liquid Jet
June 1, 2023 - ASTM International

5.1 This test method may be used to estimate the relative resistances of materials to cavitation erosion, as may be encountered for instance in pumps, hydraulic turbines, valves, hydraulic dynamometers and couplings, bearings, diesel engine cylinder liners, ship propellers, hydrofoils,...

Advertisement