loading
NEBB ENVIRONMENTAL SYSTEM - Enviromental Systems Technology
January 1, 1999 - NEBB

This publication has more than 1,020 pages written specifically for persons who need extensive information on heating, ventilating, and air-conditioning (HVAC) systems for background, reference, and practical applications. A true collector's item, this handsomely appointed, hard-back book brings...

JIS ENVIRONMENTAL MGMT - JIS Environmental Management Handbook
January 1, 2019 - JSA
A description is not available for this item.
ASTM F3227/F3227M-26 - Standard Specification for Environmental Systems in Aircraft
July 1, 2026 - ASTM International

1.1 This specification covers international standards for the environmental system aspects of airworthiness and design for "small" aircraft. 1.2 The applicant for a design approval must seek the individual guidance of their respective CAA body concerning the use of this specification as part...

ASTM D7584-16(2026) - Standard Test Method for Evaluating the Resistance of the Surface of Wet Blue and Wet White to the Growth of Fungi in an Environmental Chamber
July 1, 2026 - ASTM International

6.1 The environmental chamber method is an accelerated test for determining the resistance of Wet Blue and Wet White to the growth of fungi, the causal agent of mold. See Test Method D3273., 6.2 The environmental chamber method is useful in estimating the performance of fungicides and...

ASTM D1119-22(2026) - Standard Test Method for Percent Ash Content of Engine Coolants
August 1, 2026 - ASTM International

1.1 This test method covers the determination of ash content after ignition of commercial engine coolants and antirusts, as packaged or after use. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does...

ASTM D6008-26 - Standard Practice for Determining the Environmental Condition of Federal Property
April 1, 2026 - ASTM International

4.1 Uses-This practice is intended for use by federal agencies, and environmental professionals in order to facilitate ECP efforts. It is also intended for use by preparers and reviewers of environmental condition of property maps and ECP reports used to support CERFA uncontaminated...

ASTM D2847-22(2026) - Standard Practice for Testing Engine Coolants in Car and Light Truck Service
August 1, 2026 - ASTM International

1.1 This practice covers an updated procedure for evaluating corrosion protection and performance of an engine coolant in passenger car, light truck service that closely imitates current vehicle and engine manufacturers' practices. Note 1: Coolant evaluation in vehicle service may require...

ASTM D6752/D6752M-26 - Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method
August 1, 2026 - ASTM International

1.1 This test method covers the determination of bulk specific gravity of compacted asphalt mixtures by the vacuum sealing method. 1.2 This method can be used for compacted cylindrical and cubical laboratory and field asphalt mixture specimens. 1.3 The bulk specific gravity of the compacted asphalt...

ASTM F2199-26 - Standard Test Method for Determining Dimensional Stability and Curling Properties of Resilient Flooring after Exposure to Heat
August 1, 2026 - ASTM International

1.1 This test method covers the determination of the change in linear dimensions of resilient floor tile/plank products after exposure to heat and reconditioning to ambient temperature. 1.2 This test method allows one to also measure curling that can occur after a specimen has been exposed to heat...

ASTM D1123-22a(2026) - Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method
August 1, 2026 - ASTM International

1.1 These test methods cover the determination of the water present in new or unused glycol-based coolant concentrates using a volumetric (Test Method A) or an automatic coulometric titrator procedure (Test Method B). 1.2 Many carbonyl compounds react slowly with the Fischer reagent, causing a...

ASTM D1177-22(2026) - Standard Test Method for Freezing Point of Aqueous Engine Coolants
August 1, 2026 - ASTM International

1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory. Note 1: Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases...

ASTM F1488-26a - Standard Specification for Coextruded Composite Pipe
August 1, 2026 - ASTM International

1.1 This specification covers coextruded composite pipe, intended for non-pressure gravity flow drain waste or vent (DWV) service, or plastic underdrain service, or electrical or comunications conduit service produced by a coextrusion die system, in which the concentric layers are formed and...

ASTM F3115/F3115M-26a - Standard Specification for Structural Durability for Small Aeroplanes
August 1, 2026 - ASTM International

1.1 This specification addresses the airworthiness requirements related to structural durability for the design of small aeroplanes. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Levels 1 through 4 Normal...

ASTM F877-26 - Standard Specification for Crosslinked Polyethylene (PEX) Hot- and Cold-Water Distribution Systems
August 1, 2026 - ASTM International

1.1 This specification covers requirements, test methods, and marking requirements for system components when tested with nominal SDR9 crosslinked polyethylene (PEX) tubing as a system. Systems are intended for 100 psi (0.69 MPa) water service up to and including a maximum working temperature of...

ASTM F3519-21(2026)e1 - Standard Guide for Establishing a Reporting Structure for Exoskeleton Analysis
July 15, 2026 - ASTM International

1.1 This guide provides a structure for exoskeleton manufacturers to document their analysis. Furthermore, this guide should be used in conjunction with Practice F3474, Guide F3518, Guide F3688, and other future documents. 1.2 This standard does not purport to address all of the safety concerns, if...

ASTM D1238-26 - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
July 15, 2026 - ASTM International

1.1 This test method covers the determination of the rate of extrusion of molten thermoplastic resins using an extrusion plastometer. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with...

ASTM E1354-26 - Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
August 1, 2026 - ASTM International

1.1 This fire-test-response standard provides for measuring the response of materials exposed to controlled levels of radiant heating with or without an external ignitor. 1.2 This test method is used to determine the ignitability, heat release rates, mass loss rates, effective heat of combustion,...

Advertisement