loading
ASTM E1996-26 - Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
June 15, 2026 - ASTM International

1.1 This specification covers exterior windows, glazed curtain walls, doors, and impact protective systems used in buildings located in geographic regions that are prone to hurricanes. 1.1.1 Exception-Exterior garage doors and rolling doors are governed by...

ASTM E2112-23 - Standard Practice for Installation of Exterior Windows, Doors and Skylights
April 15, 2023 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM E283/E283M-26 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen
April 1, 2026 - ASTM International

1.1 This test method covers a standard laboratory procedure for determining the air leakage rates of exterior windows, skylights, curtain walls, and doors under specified differential pressure conditions across the specimen. The test method described is for tests with constant...

ASTM E547-00(2024) - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference
December 1, 2024 - ASTM International

1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a cyclic static air pressure at the outdoor face higher than...

ASTM E2128-26 - Standard Guide for Evaluating Water Leakage of Building Walls
July 1, 2026 - ASTM International

1.1 This guide covers methods for determining and evaluating causes of water leakage of exterior walls. For this purpose, water penetration is considered leakage, and therefore problematic, if it exceeds the planned resistance or temporary retention and drainage capacity of the wall, is...

ASTM E2112-19c - Standard Practice for Installation of Exterior Windows, Doors and Skylights
October 1, 2019 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM E1996-23 - Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
July 1, 2023 - ASTM International

1.1 This specification covers exterior windows, glazed curtain walls, doors, and impact protective systems used in buildings located in geographic regions that are prone to hurricanes. 1.1.1 Exception-Exterior garage doors and rolling doors are governed by...

ASTM E2112 - Standard Practice for Installation of Exterior Windows, Doors and Skylights
October 1, 2019 - ASTM

This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in residential...

ASTM D3678-26 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions
February 1, 2026 - ASTM International

1.1 This specification establishes requirements for the material properties, including dimensional stability and extrusion quality, of rigid, poly(vinyl chloride) (PVC) interior-profile extrusions. Methods for identifying interior-profile extrusions that comply with the requirements of this...

ASTM E2112-19b - Standard Practice for Installation of Exterior Windows, Doors and Skylights
April 15, 2019 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM E2112-19a - Standard Practice for Installation of Exterior Windows, Doors and Skylights
April 1, 2019 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM C1280-25 - Standard Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing
October 1, 2025 - ASTM International

This specification covers the minimum requirements for and the methods of application of gypsum sheathing for use as a substrate for exterior wall cladding. Gypsum sheathing board is a substrate that shall be covered by an exterior cladding or other weather-resistive barrier and is...

ASTM E330/E330M-14(2021) - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference
October 15, 2021 - ASTM International

1.1 This test method describes the determination of the structural performance of exterior windows, doors, skylights, and curtain walls under uniform static air pressure differences, using a test chamber. This test method is applicable to curtain wall assemblies including, but not...

ASTM E2112-19 - Standard Practice for Installation of Exterior Windows, Doors and Skylights
January 1, 2019 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM E2112-18b - Standard Practice for Installation of Exterior Windows, Doors and Skylights
November 15, 2018 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM E2112-18a - Standard Practice for Installation of Exterior Windows, Doors and Skylights
November 1, 2018 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

ASTM E331-00(2023) - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference
February 1, 2023 - ASTM International

1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a uniform static air pressure at the outdoor face higher than...

ASTM E1233/E1233M-14(2021) - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights, and Curtain Walls by Cyclic Air Pressure Differential
August 1, 2021 - ASTM International

1.1 This test method describes the determination of the structural performance of exterior windows, doors, skylights, and curtain walls under cyclic air pressure differential, using a test chamber. This test method is applicable to all curtain wall assemblies, including, but not...

ASTM D4726-24 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors
February 1, 2024 - ASTM International

1.1 This specification establishes requirements for the material properties, including dimensional stability, weatherability, and extrusion quality, of rigid poly(vinyl chloride) (PVC) exterior profile extrusions used for assembled windows and doors. Methods for testing and for...

ASTM E2112-18 - Standard Practice for Installation of Exterior Windows, Doors and Skylights
April 1, 2018 - ASTM International

1.1 This practice covers the installation of fenestration products in new and existing construction. For the purpose of this practice, fenestration products shall be limited to windows, sliding patio-type doors, swinging patio type doors, and skylights, as used primarily in...

Advertisement