1.1 This test method covers the determination of the rate of extrusion of molten thermoplastic resins using an extrusion plastometer. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any,...
This specification covers the standard requirements for plasticized ethyl cellulose thermoplastic compounds suitable for injection molding and extrusion. It does not however include special materials compounded for special applications. Materials shall be ethyl cellulose plastics in the form...
This specification covers melt processable molding and extrusion materials of PFA-perfluoro(alkoxy
1.1 This specification covers melt processable molding and extrusion materials of FEP resin. This specification does not cover recycled FEP materials. These FEP resins are copolymers of tetrafluoroethylene and hexafluoropropylene or modified FEP resins containing no more than 2?% by weight...
1.1 This specification covers melt processable molding and extrusion materials, as well as coating materials of poly(vinylidene fluoride) fluoroplastic, commonly abbreviated PVDF (or PVF2 in scientific literature). This specification covers thermoplastic resin materials supplied in pellet or...
1.1 This test method covers two laboratory procedures for determining the extrusion rate and application life (or "pot life") of elastomeric chemically curing sealants for use in building construction. Note 1: These sealants are supplied with various rheological properties ranging from...
1.1 This practice covers the nondestructive testing of field seams in geomembranes using the spark test. A suspect area is indicated by the generation of a spark. The test is applicable to seams made by the extrusion method, seams made by using welding tape (a strip of the same type of...
This specification covers dimensional interchangeability requirements of glass stopcocks with polytetrafluoroethyl
1.1 This specification covers brick intended for use in masonry supplying structural or facing components, or both, to the structure. 1.2 The requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining...
1.1 This specification covers thin veneer brick units made from clay, shale, fire clay, sand, or mixtures thereof, and fired to incipient fusion for use in adhered or fastened veneer applications. Three types of thin veneer brick units in each of two grades are covered. In this specification, the...
5.1 Precracked specimens offer the opportunity to use the principles of linear elastic fracture mechanics (1) to evaluate resistance to stress corrosion cracking in the presence of a pre-existing crack. This type of evaluation is not included in conventional bent beam, C-ring, U-bend, and tension...
3.1 In accordance with Specification D2227, shipments of TSR10 and TSR20 must meet a minimum initial Wallace plasticity (Po) of 30 to be accepted. However, even with this minimum restriction, the uncured viscoelastic or "processability" properties are allowed to vary greatly. This variation in...
5.1 The value, ?Kth, determined using Test Method E647 does not partition contributions of intrinsic and extrinsic effects (?Kth,i and ?Kth,x, respectively as illustrated in Fig. 2) to crack growth rate. The ?Kth measurements can be unconservative because they include a varying and indeterminant...
1.1 This classification system standard covers nonrigid vinyl chloride polymer and copolymer classes in which the resin portion of the composition contains at least 90?% vinyl chloride. The remaining 10?% can include one or more monomers copolymerized with vinyl chloride or consist of other resins...
1.1 This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable structures. 1.1.1 This specification covers two-part epoxy adhesive suitable for bonding aluminum alloy facings to nonmetallic core,...
This specification establishes requirements for the material properties, including dimensional stability and extrusion quality, of three classes of rigid, poly(vinyl chloride) (PVC) interior-profile extrusions. Methods for identifying interior-profile extrusions that comply...
This specification covers five grades of zirconium strip, sheet, and plate. These are low oxygen zirconium (Grade R60700), unalloyed zirconium (Grade R60702), zirconium-tin (Grade R60704), zirconium-niobium (Grade R60705), and zirconium-niobium (Grade R60706). The materials shall be made from...
4.1 The property KIc, determined by Test Method E399 or ISO 12135, characterizes a material's resistance to fracture in a neutral environment and in the presence of a sharp crack subjected to an applied opening force or moment within a field of high constraint to lateral plastic flow (plane strain...
This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose. The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot (cast in hollow form or pierced) and extruded by the use of the die and...
5.1 This test method is useful for quality-control tests on PVC compounds having a wide range of melt viscosities. Measurements are made at shear rates close to 1 s-1. 5.2 In addition to the properties mentioned in Test Method D1238, this technique is sensitive to plasticizer content, polymer...
Narrow Your Results