loading
ASTM D2176-26 - Standard Test Method for Folding Endurance of Paper and Plastics Film by the M.I.T. Tester
July 1, 2026 - ASTM International

4.1 The folding endurance is frequently used to estimate the ability of the paper and plastics film to withstand repeated bending, folding, and creasing. 4.2 Folding endurance has also been found useful in measuring the deterioration of paper and plastics film upon aging.

ASTM D6583-13(2026) - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
June 1, 2026 - ASTM International

1.1 This test method is applicable to air-dry architectural coatings of any type, both solvent and water-borne, and of any color, dark as well as light. It cannot be used with films that are dissolved or excessively softened by mineral oil, but practical examples of such films will be...

ASTM E2945-14(2026) - Standard Test Method for Film Permeability Determination Using Static Permeability Cells
May 15, 2026 - ASTM International

5.1 This test method provides a simple approach for determining the transmission properties of film membranes and sheeting over a range of permeability exceeding four orders of magnitude. This test method is described here to measure the permeability of films used in soil fumigation,...

ASTM E3362-26 - Standard Guide for Reference Radiographs and Digital Reference Images
July 1, 2026 - ASTM International

1.1 This guide covers the most common questions about reference radiographs and digital reference images and their use. Reference radiographs and digital reference images are used throughout industry to create acceptance specifications by identifying, categorizing, and grading discontinuities in...

ASTM D7192-26 - Standard Test Method for High Speed Puncture Properties of Plastic Films Using Load and Displacement Sensors
July 1, 2026 - ASTM International

4.1 This test method is designed to provide load versus deformation response of plastic films under essentially multi-axial deformation conditions at impact velocities. This test method further provides a measure of the rate sensitivity of the plastic films to impact. 4.2 Multi-axial...

ASTM E242-15(2026) - Standard Reference Radiographs for Appearances of Radiographic Images as Certain Parameters are Changed
July 1, 2026 - ASTM International

4.1 A key consideration with any radiographic system is its contrast resolution and spatial resolution capability (that is, sensitivity). The degree of obtainable sensitivity with a given system is dependent upon several radiographic parameters such as source energy level, film system class,...

ASTM E592-20(2026) - Standard Guide to Obtainable ASTM Equivalent Penetrameter Sensitivity for Film Radiography of Steel Plates 1 4 to 2 in. (6 to 51 mm) Thick with X-Rays and 1 to 6 in. (25 to 152 mm) Thick with Cobalt-60
July 1, 2026 - ASTM International

4.1 A key consideration with any radiographic system is its contrast resolution and spatial resolution capability (that is, sensitivity). The degree of obtainable sensitivity with a given system is dependent upon several radiographic parameters such as source energy level, film system class,...

ASTM E689-20(2026) - Standard Reference Radiographs for Ductile Iron Castings
July 1, 2026 - ASTM International

1.1 This standard extends the application of steel casting Reference Radiographs E446, E186, and E280 when performing film radiography and Digital Reference Images E2868 and E3030 when performing digital radiography to ductile iron castings when determined appropriate for specific...

ASTM E155-20(2026) - Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
July 1, 2026 - ASTM International

1.1 These reference radiographs illustrate the types and degrees of discontinuities that may be found in aluminum-alloy and magnesium-alloy castings. The castings illustrated are in thicknesses of 1/4 in. (6.35 mm) and 3/4 in. (19.1 mm). The reference radiograph films are an adjunct to this...

ASTM D4713-12(2026) - Standard Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems
June 1, 2026 - ASTM International

4.1 Nonvolatile content of printing inks is useful for specification acceptance between the producer and the user. 4.2 In order to obtain accurate results for heatset systems within the specified 3?h heating time, the specimen film thickness must be less than 100 g/m2, and the oven must have...

ASTM D2838-18(2026) - Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
April 1, 2026 - ASTM International

5.1 As a result of the manufacturing process, internal stresses are locked into the film and these can be released by heating. Note 3: For any given type of film or sheeting, the temperatures at which shrinkage will begin are related to processing techniques employed to manufacture...

ASTM D6846-02(2026) - Standard Practice for Preparing Prints of Paste Printing Inks with a Printing Gage
June 1, 2026 - ASTM International

4.1 Laboratory proofing of inks is necessary to establish a reproducible prediction of print appearance and performance properties, most of which are highly sensitive to ink film thickness. The apparatus described in this practice has found wide use for routine control proofing because it...

ASTM E390-20(2026) - Standard Reference Radiographs for Steel Fusion Welds
July 1, 2026 - ASTM International

1.1 This standard provides reference radiographs for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material. The reference radiograph films are an adjunct to this standard and must be purchased separately from ASTM...

ASTM E802-21(2026) - Standard Reference Radiographs for Gray Iron Castings Up to 412 in. (114 mm) in Thickness
July 1, 2026 - ASTM International

1.1 These reference radiographs for gray iron castings consist of one set of illustrations of centerline shrinkage with severity levels 1 to 5 using three radiation source types as follows: 1.1.1 Volume I: Medium Voltage (Nominal 250 kVp) X-ray Reference Radiographs-Set of 5 severity levels in a...

ASTM D4828-26 - Standard Test Methods for Practical Washability of Organic Coatings
June 1, 2026 - ASTM International

4.1 Interior architectural paints are subjected in use to soiling by dirt or other stains. This test method provides a way to assess relative ease of soil or stain removal from a paint film using materials common to households. This test method includes a way to evaluate the film for...

ASTM D1000-26 - Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
June 1, 2026 - ASTM International

1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: 1.1.1 Class 1-Non-elastomeric backings made from materials such as: Paper, flat or creped, Fabric, uncoated or coated, Cellulose...

ASTM F21-20(2026) - Standard Test Method for Hydrophobic Surface Films by the Atomizer Test
July 1, 2026 - ASTM International

1.1 This test method covers the detection of the presence of hydrophobic (nonwetting) films on surfaces and the presence of hydrophobic organic materials in processing environments. When properly conducted, the test will enable detection of fractional molecular layers of hydrophobic organic...

ASTM D5748-26 - Standard Test Method for Protrusion Puncture Resistance of Stretch Wrap Film
April 1, 2026 - ASTM International

4.1 Puncture resistance is very important in end-use performance of stretch wrap film used in consumer and industrial product applications. Puncture resistance is a measure of the energy-absorbing ability of a stretch wrap film in resisting a protrusion. The test method is designed to...

ASTM E192-20(2026) - Standard Reference Radiographs of Investment Steel Castings for Aerospace Applications
July 1, 2026 - ASTM International

1.1 The reference radiographs provided in the adjunct to this standard illustrate various types and degrees of discontinuities occurring in thin-wall steel investment castings. Use of this standard for the specification or grading of castings requires procurement of the adjunct reference...

ASTM E310-21(2026) - Standard Reference Radiographs for Tin Bronze Castings
July 1, 2026 - ASTM International

1.1 These reference radiographs illustrate various categories, types, and severity levels of discontinuities occurring in tin bronze and related alloy castings. The reference radiograph films are an adjunct to this document and must be purchased separately from ASTM International if needed...

Advertisement