1.1 This test method covers the determination of sediment in crude oils by membrane filtration. This test method has been validated for crude oils with sediments up to approximately 0.15?% by mass. 1.2 The accepted unit of measure for this test method is mass?%, but an equation to convert to...
1.1 Process validation of sterilizing filtration is required by industry standards and regulatory agencies to ensure that process fluid contact with the filter under actual worst-case process-use conditions (that is, time, flux, temperature, and pressure differential) do not adversely affect...
1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch by pressure filtration and gives results comparable to those obtained by Test Method D2318. 1.2 Since this test method is empirical, strict adherence to all details of the procedure is...
1.1 This test method covers the determination of dissolved elements in ground waters, surface waters, and drinking water. It may also be used for determination of total recoverable or total element concentrations in these waters as well as wastewater, mine-impacted waters, and digested biosolids,...
1.1 This practice covers a procedure for conducting on-site core flood tests to determine the filtration and chemical treatment requirements for subsurface injection of water. 1.2 This practice applies to water disposal, secondary recovery, and enhanced oil recovery projects and is...
5.1 This test method is performance oriented for determining if, and to what degree, different liquids create biological activity on geotextile filters thereby reducing their flow capability. The use of the method is primarily oriented toward landfill leachates but can be performed with any liquid...
5.1 Pressure in-line coagulation-floccula
1.1 This test method covers the determination of total oil and grease (TOG) that can be extracted from water or wastewater samples by cyclohexane and measured by non-dispersive IR spectroscopy from 1370?cm-1 to 1380?cm-1. Treating the extract with Florisil to remove polar substances prior to the IR...
This specification covers the classifications, performance requirements, and test methods for the materials used in the construction of medical face masks that are used in health care services such as surgery and patient care. Medical face mask material performance is based on testing for bacterial...
1.1 This test method covers a method for analysis of selected pesticides in a water matrix by filtration followed with liquid chromatography/elect
5.1 Hydraulic fluid compatibility is important to hydraulic equipment users because a mixture of incompatible fluids may produce a substance that is markedly inferior to its constituents. Even in identical base stocks, the formation of a precipitate may occur as a result of additive interactions....
5.1 This test method is fully quantitative and it also avoids any loss of viable organisms through wash off, making it possible to produce statistically valid data using many fewer test and control carriers than other quantitative methods based on most probable numbers (MPN). 5.2 The design of the...
1.1 This practice covers the determination of the integrity of water filtration membrane elements and systems using air based tests (pressure decay and vacuum hold), soluble dye, continuous monitoring particulate light scatter techniques, and TOC monitoring tests for the purpose of rejecting...
1.1 The purpose of this practice is to provide design and construction guidelines for contamination controlled facilities used in the assembly and integration of aerospace hardware. The guidelines herein are intended to ensure that the facilities, when used properly, will meet the cleanliness...
5.1 Turbidity is undesirable in drinking water treatment plant effluent waters, water for food and beverage processing, and for a large number of other water-dependent manufacturing processes. Removal is often accomplished by coagulation, settling, and filtration. Measurement of turbidity...
1.1 This test method covers the determination of the quinoline-insoluble matter (QI) in tar and pitch using a stainless steel filtering crucible and a filtration membrane. 1.2 This test method was evaluated in round robin testing using materials in the range of zero to twenty quinoline...
5.1 Turbidity is undesirable in drinking water, plant effluent waters, water for food and beverage processing, and for a large number of other water-dependent manufacturing processes. Removal of suspended matter is accomplished by coagulation, settling, and filtration. Measurement of...
1.1 This test method specifies the operational parameters required to perform a quantitative liquid disinfectant efficacy test against bacterial biofilm. 1.2 The test method was optimized and validated for a Pseudomonas aeruginosa or Staphylococcus aureus biofilm grown in the CDC Biofilm Reactor...
5.1 Historically, portable air cleaners were designed to remove airborne particles. More recently air cleaners have sought to also remove chemicals or airborne pathogens, or both. Concurrent with market development, there have been a range of test methods created to examine the removal or...
5.1 Historically, portable air cleaners were designed to remove airborne particles. More recently air cleaners have sought to also remove chemicals or airborne pathogens, or both. Concurrent with market development, there have been a range of test methods created to examine the removal or...
Narrow Your Results