loading
9986565 - Anaerobic, Flange Gasket
May 1, 2019 - GMNA

Material Description. A blue anaerobic polyacrylate resin base gel-like compound that solidifies by polymerization when confined between two surfaces in the absence of air or by exposure to high temperatures. When cured, the compound becomes a tough plastic material capable of providing a...

ASTM F2836-26 - Standard Practice for Gasket Constants for Bolted Joint Design
June 1, 2026 - ASTM International

1.1 This practice determines room temperature gasket tightness design constants for pressurized bolted flanged connections such as those designed in accordance with the ASME Boiler and Pressure Vessel Code. 1.2 This practice applies mainly to all types of circular gasket...

ASTM F2716-08(2026) - Standard Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam
June 1, 2026 - ASTM International

1.1 This practice provides a means of comparing various nonmetallic flat gasket materials, Classification F104, in saturated steam service under controlled conditions. While the practice is designed primarily for flat gaskets, it also can be applied to various form-in-place...

DS/EN 1514-2 - Flanges and their joints – Gaskets for PN-designated flanges – Part 2: Spiral wound gaskets for use with steel flanges
February 1, 2021 - DS

This part of EN 1514 specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with the requirements of EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 and PN 160 and up to and including DN 1 000. NOTE...

ASTM F607-03(2025) - Standard Test Method for Adhesion of Gasket Materials to Metal Surfaces
December 1, 2025 - ASTM International

4.1 This test method provides terms such as megapascals or pounds-force per square inch of gasket surface for expressing the extent of adhesion applicable to all materials within the scope of Classification System F104. Under certain conditions, adhesion develops when gasket materials...

MIL-DTL-24211 - GASKETS, WAVEGUIDE FLANGE GENERAL SPECIFICATION FOR
January 20, 2021 - NPFC

Scope. This specification covers the general requirements for pressure sealing gaskets used with general purpose cover flanges and flat face flanges covered by MIL-DTL-3922.

DS/CEN/TR 1591-2 - Flanges and their joints – Design rules for gasketed circular flange connections – Part 2: Gasket parameters
March 9, 2020 - DS

This document details generic gasket parameters for use in EN 1591-1 during preliminary calculations during which the type of gasket to be used in an application is to be decided. Once the gasket type has been decided the parameters for gaskets of that type from the...

ASTM E2734/E2734M-10(2025) - Standard Specification for Dimensions of Knife-Edge Flanges
December 1, 2025 - ASTM International

1.1 This standard specifies the dimensions of knife-edge style flanges and their associated gaskets used in vacuum systems for pressures ranging from 105 Pa to 10-11 Pa. Such flanges are widely used throughout vacuum technology applications in semiconductor processing tools,...

ASTM F363-99(2025) - Standard Test Method for Corrosion Testing of Gaskets
December 1, 2025 - ASTM International

3.1 This test method is designed to compare all types of gaskets under simulated field operating conditions. Performance of a gasket can thus be measured prior to the start-up of chemical processes.5 The design of the test unit provides maximum range of corrosion resistance so that...

ASTM F2836-18(2024) - Standard Practice for Gasket Constants for Bolted Joint Design
September 1, 2024 - ASTM International

1.1 This practice determines room temperature gasket tightness design constants for pressurized bolted flanged connections such as those designed in accordance with the ASME Boiler and Pressure Vessel Code. 1.2 This practice applies mainly to all types of circular gasket...

ASTM F37-06(2024) - Standard Test Methods for Sealability of Gasket Materials
September 1, 2024 - ASTM International

1.1 These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials at room temperature. Test Method A is restricted to liquid leakage measurements, whereas Test Method B may be used for both liquid and gas leakage measurements. 1.2...

ASTM F38-18(2024) - Standard Test Methods for Creep Relaxation of a Gasket Material
September 1, 2024 - ASTM International

4.1 These test methods are designed to compare related materials under controlled conditions and their ability to maintain a given compressive stress as a function of time. A portion of the torque loss on the bolted flange is a result of creep relaxation. Torque loss can also be caused by...

ASTM F3270/F3270M-17(2024) - Standard Practice for Compression versus Load Properties of Gasket Materials
September 1, 2024 - ASTM International

1.1 This practice measures the compression properties of a gasket material by measuring gasket deflection while it is subjected to an increasing compressive load until a target load is reached. The load and change in thickness are recorded at a defined loading rate as a function of...

ASTM F2467-06(2024) - Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications
September 1, 2024 - ASTM International

1.1 This practice covers a standard means for measuring initial static sealing pressure in transportation applications. 1.2 It uses a pressure-indicating film (PIF) that will record the maximum load imprint of the seal-to-flange interfaces. The imprints will vary in intensity based on load...

ASTM F645-25 - Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
March 1, 2025 - ASTM International

1.1 This guide is intended for use in the selection, design, and installation of thermoplastic water-pressure piping systems. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials, methods of joining, system design factor, and any...

DIN 28090-3 - Static gaskets for flange connections - Gaskets made from sheets - Part 3: Chemical resistance test procedures
November 1, 2014 - DIN

This standard applies to the testing of sheet gasket materials as specified in DIN 28091-1 to DIN 28091-4 and the gaskets produced from such materials.

AS90484A - GASKET, FLANGE MOUNT, CONNECTOR, ELECTRIC
December 20, 2011 - SAE International
A description is not available for this item.
ASME B16.20 - Metallic Gaskets for Pipe Flanges
December 29, 2017 - ASME

This Standard covers materials, dimensions, tolerances, and markings for metal ring-joint gaskets, spiral-wound metal gaskets, metal-jacketed gaskets, and grooved metal gaskets with covering layers. These gaskets are dimensionally suitable for use with...

Advertisement