This comprehensive review of calibration provides an excellent foundation for understanding principles and applications of the most frequently performed tasks of a technician. Topics addressed include terminology, bench vs. field calibration, loop vs. individual instrument...
1.1 This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from?-130?°C to ?+800?°C. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 Computer or...
1.1 This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from − 130 °C to + 800 °C. 1.2 Values given in SI units are to be regarded as the standard. 1.3 Computer or electronic based instruments, techniques or data manipulation...
5.1 This method is suitable for determining the total heat of hydration of hydraulic cement at constant temperature at ages up to 7 days to confirm specification compliance. 5.2 This method compliments Practice C1679 by providing details of calorimeter equipment, calibration, and operation....
1.1 This test method is used to establish the concentration of free cyanide in an aqueous wastewater, effluent and in-stream free cyanide concentrations after mixing treated water with receiving water. The test conditions of this test method are used to measure free cyanide (HCN and CN-) and...
This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from − 130°C to +800°C. The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Computer or electronic...
Differential scanning calorimetry is used to determine the heat or enthalpy of transition. For this information to be meaningful in an absolute sense, heat flow calibration of the apparatus or comparison of the resulting data to that of a known standard is required. This practice is...
4.1 A variety of irradiation processes use low-energy electron beam facilities to modify product characteristics. Dosimetry requirements, the number and frequency of measurements, and recordkeeping requirements will vary depending on the type and end use of the products being processed. Dosimetry...
1.1 This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from − 130°C to +800°C. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 Computer or...
5.1 The energy input rate test is used to confirm that the booster heater is operating properly prior to further testing. 5.2 Booster heater flow capacity is an indicator of the booster heater's ability to supply hot water for sanitation. The booster heater's flow capacity can be used...
1.1 This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from -130°C to +800°C. 1.2 This practice may involve the use of hazardous materials, operations, and equipment. It is the responsibility of whoever uses this...
This test method establishes the apparatuses required, calibration and precision of the devices to be used, and the standard procedures for determining the measured speed, or volumetric flow rate, of oil diffusion pumps. This method shall make use of test dome, gage attachment or...
1.1 This test method covers the measurement of steady-state primary photocurrent, Ipp, generated in semiconductor devices when these devices are exposed to ionizing radiation. These procedures are intended for the measurement of photocurrents greater than 10-9 A·s/Gy(Si or Ge), in cases for which...
1.1 This guide describes the evaluation and calibration of friction measurement systems which are known as Continuous Friction Measuring Equipment (CFMEs). The evaluation and calibration processes, using the specialized equipment, instruments, pavement surfaces, trained personnel, and...
1.1 This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels.2 This test method uses a Ford Ranger 2.3?L four-cylinder engine. This test method includes detailed information regarding the procedure,...
5.1 Turbidity is undesirable in drinking water treatment plant effluent waters, water for food and beverage processing, and for a large number of other water-dependent manufacturing processes. Removal is often accomplished by coagulation, settling, and filtration. Measurement of turbidity provides...
5.1 The CCS apparent viscosity of automotive engine oils correlates with low temperature engine cranking. CCS apparent viscosity is not suitable for predicting low temperature flow to the engine oil pump and oil distribution system. Engine cranking data were measured by the Coordinating...
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856 kg or less. The tests are conducted using a specified spark-ignition engine with a...
1.1 This test method covers an engine test procedure for the measurement of the effects of automotive engine oils on the fuel economy of passenger cars and light-duty trucks with gross vehicle weight 3856?kg or less. The tests are conducted using a specified spark-ignition engine with a...
Narrow Your Results