loading
IEEE COMPUTER COMMUNICATE - COMPUTER COMMUNICATIONS AND NETWORKS
IEEE
A description is not available for this item.
IEEE COMPUTER PIONEERS - COMPUTER PIONEERS
IEEE
A description is not available for this item.
IEEE COMPUTER-AIDED - COMPUTER-AIDED DESIGN OF ANALOG INTEGRATED CIRCUITS
IEEE
A description is not available for this item.
TEMA FLOW INDUCED - Flow Induced Vibration Analysis Software (FIV)
TEMA
A description is not available for this item.
DIN EN 12405-3 - Gas meters - Conversion devices - Part 3: Flow computer
April 1, 2016 - DIN

Part 3 of this European Standard specifies the requirements and tests for the construction, performance, safety and conformity of flow computers (FCs) used to meet the metrological and technical requirements of a high accuracy volume conversion device. They are used to determine...

DS/EN 12405-3 - Gas meters - Conversion devices - Part 3: Flow computer
January 12, 2016 - DS

Part 3 of this European Standard specifies the requirements and tests for the construction, performance, safety and conformity of flow computers (FCs) used to meet the metrological and technical requirements of a high accuracy volume conversion device. They are used to determine...

AENOR UNE-EN 12405-3 - Gas meters - Conversion devices - Part 3: Flow computer
October 11, 2016 - AENOR
A description is not available for this item.
AENOR UNE-EN 12405-3 ENG - Gas meters - Conversion devices - Part 3: Flow computer
October 11, 2016 - AENOR
A description is not available for this item.
BS EN 12405-3 - Gas meters — Conversion devices Part 3: Flow computer
December 31, 2015 - BSI
A description is not available for this item.
ASTM F448-26 - Standard Test Method for Measuring Steady-State Primary Photocurrent
February 1, 2026 - ASTM International

5.1 PN Junction Diode-The steady-state photocurrent of a simple p-n junction diode is a directly measurable quantity that can be directly related to device response over a wide range of ionizing radiation. For more complex devices, the junction photocurrent may not be directly related to device...

ASTM F3427-25 - Standard Practice for Documenting Environmental Conditions for Utilization with Exoskeleton Test Methods
November 1, 2025 - ASTM International

4.1 This section provides a description of the environmental conditions listed in Section 1 and describes the sub-conditions within each condition. Examples provided for many of the conditions and sub-conditions are provided as guidance only. Each of the conditions described should be evaluated and...

ASTM E968-25 - Standard Practice for Heat Flow Calibration of Differential Scanning Calorimeters
April 1, 2025 - ASTM International

1.1 This practice covers the heat flow calibration of differential scanning calorimeters over the temperature range from?-130?°C to ?+800?°C. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 Computer or...

ASTM D2885-21(2025) - Standard Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique
October 1, 2025 - ASTM International

5.1 The delta octane number (?O.N.) measure can quantify the difference of in-line blended spark-ignition engine fuel or process stream material octane number to a desired octane number to aid in optimizing control of blender facilities or refinery process units. 5.2 The ?O.N. measure, summed with...

ASTM D2885-21(2025)e1 - Standard Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique
October 1, 2025 - ASTM International

5.1 The delta octane number (?O.N.) measure can quantify the difference of in-line blended spark-ignition engine fuel or process stream material octane number to a desired octane number to aid in optimizing control of blender facilities or refinery process units. 5.2 The ?O.N. measure, summed with...

ASTM D6235-25 - Standard Practice for Expedited Site Characterization of Vadose Zone and Groundwater Contamination at Hazardous Waste Contaminated Sites
July 1, 2025 - ASTM International

1.1 Applicability of the ESC Process-This practice covers a process for expedited site characterization (ESC) of hazardous waste contaminated sites2 to identify vadose zone, groundwater and other relevant contaminant migration pathways and determine the distribution, concentration, and fate of...

PREN 12405-3 - GAS METERS - CONVERSION DEVICES - PART 3: FLOW COMPUTER
BSI
A description is not available for this item.
AGA XQ8805 - Gas Measurement Manual - Part 8: Electronic Flow Computers and Transducers
January 1, 1988 - AGA
A description is not available for this item.
ASTM F3286-17(2024) - Standard Guide for Cybersecurity and Cyberattack Mitigation
November 15, 2024 - ASTM International

5.1 To maintain the integrity of potentially vulnerable information systems while the vessel is at sea or in port, strategies and procedures can be used by every company, organization, and ship. Mitigating potential cyberattack events will allow for a better economic environment through secure...

Advertisement